20 Most Recent
HP LaserJet 4 plus Printer - Page 9 Questions & Answers
Will not come on
Check the power cable and the where the printer is connected, if connected through a surge connect directly to the wall. If the printer is still not responding it could be the low voltage power supply, and would require to be serviced.
Al
[email protected]
Hewlett packard laserjet4. will not come on
If the printer will not power up, you may need to replace the power supply. It should be less than $100 and should take a repair person less than 45 minutes to accomplish.
ME Feed C5
THE DOCUMENT WAS SAVED AS A C5 "SIZE" OF PAPER AND THE PRINTER IS ASKING YOU TO PUT THAT SIZE PAPER IN THE MANUAL FEEDER. HAVE THE PDF FILE RECREATED IF POSSIBLE AND SAVE IT AS THE APPROPRIATE SIZE PAPER.
21 print overrun
This prompt comes when the printing documents are too complex. At this time press continue it may start the printing and to remove the problem for future follow the steps as bellow.
Click Start-Settings-Printers .
Highlight the HP LaserJet 4 icon.
Choose File and verify there is a check by Set as Default-Choose Properties-select Device Options and verify the memory setting shown here is the same as what the printer has installed.
Select the page protection option and then choose OK .
Close out of the Printers folder and try printing again.
I have an envelope feeder that came with my old
My suspiction is there is a tab on the tray that triggers a switch telling the printer what type of tray has been inserted. Your old tray is likely different from the Plus 4 tray and the printer knows it.
Toner showing low but its refilled newly
By using refilled toner cartridges you will always get this type of indication becuase the chip on the cartridge cannot be reset. The best kind of refills to purchase are when they replace the chip and other main components on the cartridge such as the chip and drum unit. If they are only refilling the same cartridge over and over again and not replacing these main components you will start seeing quality issues to your print.
Paper jams as it heads for the heater. It oges
Paper jams in the fuser (rear of the printer) are often caused by worn gears in the fusing assembly. This is usually one of the sysmptoms as well as a clicking or grinding noise which comes from the gears slipping. The solution is to replace the fuser. It is an easy fix that does not require a technician. There are only two screws that hold the fuser in place. Search for a fuser online. With shipping it should not cost you more than $75. If you are really mechanically inclined you could search just for the fuser gears but that really does require that you know what you are doing.
Manual Feed
Press the first button on the left bottom side (shift) and meanwile the third button on the left bottom side (continue). And then it should do the job.
Paper under toner cartridge
user gear might b broken. Open rear door, you will see the fuser assembly(be carefull HOT SURFACE) Unscrew to screws at the bottom of the plat and check the gears on the side.
Good luck
13 Printer Jam Problem
If it is jamming under the toner (meaning the paper is not quite reaching the toner cartridge, and "crinkling" up), then you would be correct. There may be a tiny pipce or chunk of paper creating a "well" and stopping the paper. If you remove the paper tray and the cartridge, and flip the machine on it's back (fuser side), you may be able to see the chunk in the paper path. You could also get a sturdy pice of laminated paper or card stock, at least an inch or two wide, and run it backwards thru the path to try to back out the chunk.
If the paper is just stopping, in any other spot than the paper tray, it could be a dirty or dead sensor. Try removing the cartridge and spraying canned air throughout the machine.
Can i connect hp laserjet 4p via usb ??
I have a similar situation. Trying to print from a HP LaserJet 4 using a parallel cable to USB. It will not recognize the printer. What is the installation setup or what is the trick to get it to print?
My LaserJer 4 plus printer fails to print
Could be a fuser or bad toner or bad pick up rollers. Check all 3 and eamil me back. Need more information. Does it try to print after you send a job? does it have power? Is there any error codes?
Not finding what you are looking for?