The gas shutoff solenoid on your John Deere LA 130 is typically located on the bottom of the carburetor bowl, and it should be screwed in to secure it in place. If you have been turning the solenoid for 20 minutes without it coming off, it's possible that it may be stuck or there could be another issue preventing it from loosening.
Here are a few things you can try:
1. Apply penetrating oil: Spray some penetrating oil (such as WD-40) around the base of the solenoid where it screws into the carburetor bowl. This can help loosen any debris or corrosion that may be causing it to stick.
2. Use a wrench or pliers: If the solenoid has a hexagonal base, you can try using an appropriately sized wrench to provide additional leverage for turning it. Alternatively, you can use pliers to grip the solenoid tightly and turn it counterclockwise.
3. Seek professional help: If the solenoid still doesn't come off after attempting the above steps, it might be best to consult a professional technician or take your mower to an authorized John Deere service center. They will have the necessary expertise and tools to diagnose and resolve the issue safely.
Remember to exercise caution while working on your mower's carburetor and ensure the engine is turned off and cool before attempting any repairs.
Question edited for typo.
Two person job. Spray the locking lugs with WD40. One person holds the machine and the other turns the bowl anticlockwise.
Full 'make model (what it is)' is useful in these questions.
..
In the drive train there are shear pins that are soft enough to shear if the gears are strained. It happens on bread dough if you run the machine too fast or put a piece of bone into a grinder attachment.
Or, sometimes a gear will move. if not correctly shimmed.
https://www.google.com/search?q=Haden+Mixer+parts+diagram
..
The machine needs stripping down as something it likely worn. The gearbox is also packed with grease and may need re-packing. They do need periodic servicing. Does it make the same noise with the bowl removed? Sometimes the noise will be attachments hitting the bowl. There is an adjustment screw underneath to see clearance.
https://www.google.com/search?q=SMEG+Stand+Mixer+makes+loud+clanging+noise
..
There are several potential reasons why your KitchenAid dough mixer might be shutting off. Here are a few possible causes:
Overheating: If the mixer has been running for an extended period of time, the motor may overheat and shut off as a safety precaution. In this case, you should allow the mixer to cool down for a while before using it again.
Faulty wiring: If the mixer is shutting off when you turn it on or when you change the speed, there may be a problem with the wiring. You should check the wiring to see if there are any frayed or damaged wires that could be causing the issue.
Clogged air vents: The mixer may shut off if the air vents are clogged, as this can cause the motor to overheat. You should check the air vents to make sure they are clean and unobstructed.
Failed motor: If none of the above issues are present, the problem could be with the motor itself. A failed motor can cause the mixer to shut off, and it may need to be replaced.
If you are not comfortable troubleshooting the mixer yourself, you should consider contacting KitchenAid customer service or a professional appliance repair service for assistance.
Hi,
This sounds like it's a portion of the whole product. If you want that, you might need to arrange an order through nuwave or one of it's manufacturer partners that focuses on the plastic enclosure tha that you've mentioned. If that does not work, then you can reach out to a commercial kitchen product distributor to help with find the part. To find one, you can check on the back of your kitchen product boxes . They sometimes show a "distributed by" phrase in those areas.
Thank you.
Tip it on its side and spray it with kitchen cleaner spray. Wait 5 minutes and try again. It is probably gummed up from a messy cake job.
FULL 'make model (what it is)' in all questions please, first 3 words.
..
Hi,
apply some cooking oil to where the parts are connected. If that fails, please submerge the parts in a bucket of or tube of water and attempt to detach them from each other. If all else fails, please reference the manual to ensure that you've not missed a detachment procedure.
Thank you.
The sparks are generally seen where the carbon brushes meet the copper commutator on the motor spindle. This is actually fairly normal. You can lessen it by spraying with some light machine oil, but eventually you will need to replace the carbon brushes.
![Westinghouse Westingtinghouse 3-speed Hand Mixer, Model Wwmx3 [new In Box] Logo](https://www.fixya.com/fixya20/products/w/westinghouse/118x100/westingtinghouse_3speed_hand_m_q3407266.jpg "Westinghouse Westingtinghouse 3-speed Hand Mixer, Model Wwmx3 [new In Box]")
