20 Most Recent GE Profile Spacemaker Stainless Steel Refrigerator Gmr04hascs Dorm/office Fridge - Page 5 Questions & Answers

Hi, if your water is overfilling then you probably need a faceplate for your icemaker. If you remove the cover on your icemaker(pry on the corners and pull at same time) You will see a screw with a spring on it. That adjust the water flow. If you tighten you decrease the water. Make sure the gears are not corrioded. If it is. Replace the plate with the gears on it.

Bad relay or bad compressor.

Freezer repair in Corona Del Mar, CA
Appliance repair in Corona Del Mar and Orange County, CA

his normally could be a bad start relay and over load for the compressor, dirty condenser coils need cleaning, condenser fan motor is not running or the compressor itself. To check the compressor properly you should test it with an amp meter, each compressor is rated in running amps ( see model/serial tag or the sticker on the compressor )...if the compressor is drawing too much current, this may be why it is shutting off. Check the model tag for proper amp rating. Some relays will be easy to notice the broken with them, they may be burnt.

remove the rear cover inside the freezer if it has a lot of frost on it,then the evaporator coil is frozen up and you cant blow cold air over or thru a solid block of ice,defrost it,then check the defrost heating element,defrost thermostat and timer or defrost circuitry for no power or defective components,you can use a hand held hair dryer to defrost it quicker

Good day,
If replacing the relay and overload didn't help, then it is an internal problem in the compressor itself.
If the machine is under 5 years of age, then it is under factory warrant. Call your selling dealer for details, otherwise you have a major problem. You will need the services of a pro and it will be expensive.

the compressor will run hot,but you should be able to touch it without burning yourself.(when you compress a gas, heat is generated as it turns to liquid and when it expands back to a gas it absorbs heat,the principal of a fridge...)

ok what you need to do is take a hair drier and soffen the gasket with the blowdrier or heat vgun and set it as cold as you can soffen the whole gasket ,,,dont burn it and then shut it tight and use tape to keep iy shut for about 3-4 hrs and it should seal; jaason

Craigs list

freezer may be iced up,defrost it and try again

The water that is pooling and freezing inside the bottom of your GE freezer is definitely coming from the defrost cycle. It does this because the freezer compartment inside the back of your freezer intended to carry the defrost water down to the external evaporator tray is blocked with ice. As a result, the defrost water from the coils overflow the collector under the coils and run down the inside back of your freezer and then the water pools on the bottom and re-freezes when the cycle is over. Unplug the unit for 36 hours and let it completely melt. You can also remove the freezer drawer and melt it away with hot water or use a blow dryer to melt the ice.

Hi,

Many times a freezer and/or refrigerator do not work right because of a dirty condenser coil...there are also many other things that can go wrong.

If you are hearing a clicking or buzzing then check out the last two tips.

If your refrigerator is running but warm, then…

Check out this tip that I wrote about that... it is a great place to start trouble shooting your unit...and something that you can do rather then calling a repair person to do a simple thing for you...

Refrigerator Condenser Coil Cleaning Refrigerator Repair

Refrigerator Troubleshooting Refrigerator Compressor

Refrigerator Compressor Start Capacitor and Start Relay


heatman101

dear sir/madam '
make sure first your freezer,s compressor is working .if it,s working or not cooling there then make thermostat setting correct and check if it,s yet same problem then there is low gas problem . for refill gas contact to your service technician .

hope answer the questoin
thank you
please vote!

May I get the model # so I can help you find the filter

May I get the model # of the freezer so I can help you more

On the evap coil.

#240 on THIS DIAGRAM

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Thanks for your question!

I'm sorry that you haven't received an answer yet.

The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...

Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.

Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Thanks for your question!

I'm sorry that you haven't received an answer yet.

The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...

Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.

Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question