20 Most Recent Krups Km7000 10-Cup Grind-and-Brew Coffeemaker Black - Page 3 Questions & Answers

Try this, remove the tank, the drip tray, the bin on the side and the sliding thing above the bin. Hold down the on and steam buttons while plugging the machine into a live socket, it's either that or the same again but holding down the on button and the program button while plugging it in. You will get a screen that says something like " Remis a something vende" which is French for put it into sale state, you choose "Oui" for yes. It's been a long time since I've done one but that's as best as I can recall. It will zero the coffee counters as well. https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk02VetSw_f-MdUcfZ3oveWE2qJRjhQ:1604423278014&q=Krups+EA880810.+How+can+I+hard+reset ..

It can cause problems if it doesn't work correctly. To test the thermostat in a drip coffee maker: Step 1: Unplug the unit, empty excess water from the reservoir, turn the unit over, and remove the base. ... Step 3: If defective, remove and replace the thermostat with one of the same rating. https://home.howstuffworks.com/how-to-repair-small-appliances3.htm

Error code 5 is a result of one of the following:

Blocked water circuit (water meter, pump, distributor, distributor motor, microswitch)

Hi! Did You fixed the problem? I got same error and have no idea whats the point :(

No thermoblock heating. Here is broken two thermo fuses on the thermoblock.

Krups manuals here https://www.krupsusa.com/instructions-for-use/Products/Beverages/Espresso/csc/Espresso Are you in the USA or Europe?

That model had a likelihood of the electrovalve growing a green crystal inside the fitting where the teflon tube comes from the boiler. The electrovalve is a solenoid operated tap on the steam wand side accessed by removing the lid and the side cover. I used to take the electrovalve off completely to do the job. To get the teflon tube out you depress the silver collar around the tube towards the fitting and pull on the tube. It won't come out unless you depress the collar. You then unscrew that same fitting and clear the green crystal out with a probe or screwdriver and rinse or blow the fitting out. The fitting was sealed from new into the electrovalve with some sort of sealant product, I used to clean out the threads and use some thread tape, I never had a leak and did heaps of them over the years.

Found on the internet:

Try this, remove the tank, the drip tray, the bin on the side and the sliding thing above the bin. Hold down the on and steam buttons while plugging the machine into a live socket, it's either that or the same again but holding down the on button and the program button while plugging it in. You will get a screen that says something like " Remis a something vende" which is French for put it into sale state, you choose "Oui" for yes Hope this helps

I found this on the internet:

Try this, remove the tank, the drip tray, the bin on the side and the sliding thing above the bin. Hold down the on and steam buttons while plugging the machine into a live socket, it's either that or the same again but holding down the on button and the program button while plugging it in. You will get a screen that says something like " Remis a something vende" which is French for put it into sale state, you choose "Oui" for yes

https://ersatzteildirect.de/de/Krups-Kaffeemaschine-Behaelter-Becken-EA9000-EA9010::7990.html

Hello Linda Foster, If there is NOT an OWNERS MANUAL immediately available.. there are a huge selection of KRUPPS machines... Chose from the attached list... Find the trouble section... Read & heed Results for krupps coffee maker var myCallback function document ready... Hope this helps... (or REPOST with model number for BETTER QUALITY answers). Carnac the Magnificent

You need to ask a better question that includes the model number and exactly what program or part of the program you have issues with.

what is your modle sir

You can only get that wheel as part of the grinder, it is not possible to remove the burr to replace the plastic part. It's factory fit during manufacture. There are 2 reasons I'm aware of to cause that, rarely it can be a stone in the beans but more likely you have an internal leak causing the grounds to bind up together from the steamy environment within the housings. Also if the relief valve in the distributor is sticking it can cause the chamber to stay very wet.

Error 12 There was no pulse from the ejection switch so possibly a switch problem or worse still some grief on the control PCB. This will also be associated with the cleaning the drawer problem. From memory the switch/es are located above the used grounds bin.

my dear sir it looks that you had some internal leaking .due to this the water went on to the electric parts . now you need to fest dry it properly then plug it in again and make sure it doesn't leak again if not check there is two thermal fuse on the ac supply sow make sure you unplug first see that you do the same as type if this get blown again then you have to change the pcb

Hello, Roos - You may find the instructions here helpful: https://www.thespruceeats.com/how-to-make-yogurt-in-an-electric-yogurt-maker-909013 Best wishes.