Sony DPP-FP50 Thermal Photo Printer - Page 4 - Answered Questions & Fixed issues
My sony projector keep turning of and red at lamb/cover is blinking
I used to work in the AV support department for a large university where we maintained about a hundred projectors in-house. Here is how we approached your kind of problem:
- Most likely cause is high temp caused by lack of air flow, try these:
- Clean air filter and/or louvers, both intake and exhaust
- Make sure air intake and exhaust louvers are not blocked by external objects when in use - that can raise temp to point of shut-off
- Next most likely causes: bad fan motor or a failed sensor.
- Bad fan motor - fans can bog down if the bearings go bad; you may notice an unusual noise, typically a whining sound.
- Failed sensor There are two types: temperature and airflow.
- To fix either of these, or anything else, requires opening the projector.
- Unless you are a qualified electronic service technician (preferably with service manual and access to OEM replacement parts), this is a job for the authorized service center. Not only can you ruin the projector, you also risk fire, exploding projector lamp, and electrocution, as well as other hazards to life, limb, and property.
- Is the unit still under warranty? Many projectors are covered for three years. If you bought it with a credit card with free extended warranty (comes with most gold level cards), you should have an additional year through the credit card company.
- Unlikely, but possible causes: loose connector, bad solder joint, defective circuit component(s), etc. As above, diagnosing and repairing is a job for the service center.
Good luck! Please let me know if this was helpful in fixing the problem, or knowing when to send our for repair, or saving money. Thanks!
2/21/2015 3:39:43 PM •
Sony Office...
•
Answered
on Feb 21, 2015
•
652 views
I want install for my computer window7 sony DPP-FP30printer
I checked an this printer can only be used with Windows XP. No drivers are available for it anymore unless you try to load the Windows 7 in the backward legacy use. It might work. This is very old so I am not betting on it. Good luck
1/27/2015 1:22:03 PM •
Sony Office...
•
Answered
on Jan 27, 2015
•
145 views
Lamp or temp light blinge set not work
check the lamp first
any questions, feel free to contact me
We supply original projector lamp,bulb,accessories,Lcd panel,Lens,DMD chip,color wheel,motherboard,powersupply,ballast... with high quality and competitive price.
have a nice day!
Jerry,Lampdeng Limited
3/24/2014 1:31:44 PM •
Sony Office...
•
Answered
on Mar 24, 2014
•
44 views
Crius projector
any questions, feel free to contact me
We supply original projector lamp,bulb,accessories,Lcd panel,Lens,DMD chip,color wheel,motherboard,powersupply,ballast... with high quality and competitive price.
have a nice day!
Jerry,Lampdeng Limited
3/24/2014 1:25:15 PM •
Sony Office...
•
Answered
on Mar 24, 2014
•
498 views
Sony vpl-cx21 video conector not working
it seems that the mother board is failing, the mother board drives the video connector.
suggestion:
change the solution of the computer,(1024*768 to 800*600,,)
any questions, feel free to contact me
We supply original projector lamp,bulb,accessories,Lcd panel,Lens,DMD
chip,color wheel,motherboard,powersupply,ballast... with high quality and
competitive price.
have a nice day!
Jerry,Lampdeng Limited
skype:lampdeng
3/21/2014 8:24:20 AM •
Sony Office...
•
Answered
on Mar 21, 2014
•
86 views
Infocus x21
is the image black and white?
if it is only black and white, there is no color ,
it seems,the Color wheel is defective
Have a good day!
We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, motherboard,
powersupply ... with high quality and competitive price.
Jerry China Lampdeng Limited
Tel: +86 131788 67858
E-mail:
[email protected]
Skype: lampdeng.com
YM:
[email protected]
http://facebook.com/lampdeng
http://www.lampdeng.com
2/21/2014 1:00:57 PM •
Sony Office...
•
Answered
on Feb 21, 2014
•
48 views
How do I fix Lamp/Cover flashing light?
There is a switch or a button that gets depressed when you close the lid of the lamp compartment. See if the plastic of the lid is broken or not hitting it right. Not screwed down right or the lamp is not seated all the way down.
12/20/2012 2:53:22 PM •
Sony Office...
•
Answered
on Dec 20, 2012
•
714 views
Not finding what you are looking for?