20 Most Recent Sharp AL-1651CS All-In-One Laser Printer Questions & Answers

your copier heater lamp is already busted

turn the power off remove catridge then check there is not any paper jam also check in back side.
then if problem remains then open the front chip bord in centre pull it then refix ram after clean dust from its.also reset your printer settings to factory defauts

L1 or L1-00 indicates Scanner movement failure. The scanner is the part under the glass that lights up and moves back and forth. So if you lift up the feeder so you can see the glass, turn the machine off for a few seconds then back on. Watch the movement of the scanner. It should move right and inch or two then back to the left. If all goes well the copier should come to ready. Lay a piece of paper on the glass and press the print button to watch the scanner movement. If it binds up or does not scan correctly there are 2 possibilities.
1) your scanner lock is engaged and is preventing the scanner from moving. Check the clear plastic dial located under the far left upper side of the copier, near where the paper exits the machine. Make sure it is in the unlocked position.
2) Your scanner rail is dirty and dry. This rail can be seen under the glass towards the back of the copier. The scanner rides on this rail. It is very common for these to get dirty and for the grease to dry up causing the scanner to freeze up on the rail. The glass must be removed and the rail cleaned and lubricated.
Just power off then on the copier to reset.

Go to this site. It's in Poland:
http://esupport.sharp.pl/html/driver/index.php?StartRec=0&ListLimit=10&TemplateLang=en&Lang=%&ProdLine=34&SortOrder=DESC&OrderBy=Title&OS=%&EMU=%&SearchString=

no there is not a detault IP address on a printer - A printer is managed from a PC in your network. You can then share that printer using the print spooler of that PC but all print requests will go through the print spooler PC.

Hi there!

To reset the drum light you need to press the following keys in sequence with 4 seconds for the initial 4 keys
Step 1: You need to press "C" then please press the far left key ( called exposure mode key) then press the "C" key then the far left key once again.
So the sequence is -- C, far left, C, far left.
Note: Some model utilize two other initial codes, you might need to use one of those two alternate codes to get your display to go blank. The remainder of the procedure is absolutely the same.
The alternate codes are as follows: #, * , C, * or pound key ,star key, C, star key and also #, Interrupt key, C, Interrupt key.
If done correctly the display will go blank.
Then type in 24 as if you are going to print 24 copies of something.
Then press the "print" button.
Then type in 7 as if you are making 7 copies
Now press the print button once again.
You will now get flashing zero's on the display of the unit.
Turn the machine off and then on again and your drum light will be gone.

http://www.fixya.com/support/r3798552-sharp_al_series_copier_drum_light

My Canon PC795 copier returns EO when I try to power it on. The unit does not power on. Please HELP!!!! Thanks.
HUGGER

There is a big gap on the left-hand side of the printer, where printed pages come out. If you stick your head down and look at the "roof" of the gap, you'll see a clear knob that locks the scanning head for transport. Turn the knob towards the front of the printer and it should clear this error code. (Source: Sharp AL-1651CS Service Manual.)

it is code for laser unite

have you try unplugging the cable and plug it again.?

Did you check the switch under the scanner. This is a lock for shipping if it is still locked it could cause this problem.
Gary

Is the new one a compatible or a sharpe original if compat fit a new original as this maybe the cause if an original check and clean all the contacts or you just might simply have a faulty drum unit.

Thanks J