Honda outboard - Answered Questions & Fixed issues

Hello, everyone.
The engine is generally healthy and what bugs me the most, has JUST been overhauled by a good mechanic, which included cleaning the carb, after which it started on 1-3 pulls and ran like magic.
Today I went fishing for the first time after not using the boat for about 3 weeks. The engine started fine (with 2/3 choke), I let it warm up a bit, with little-to-none choke. Idle was a tiny bit rough, but nothing major. When I set it on idle for the first time, it ran for about 3 minutes and died. Since then I could only start it with either choke or some throttle and it'd always die quite soon on idle or close to idle. When I try to start it warm with no choke, it'd sound as if it catches and dies off immediately.
The plugs are 1 month old and adjusted, oil's in order, no detectable problems with the prop or anything else.

I have a suspicion it might be either condensate or some grit in the fuel tank, which was stored in a rather damp place for 3 weeks, half full (although tightly closed). What should I check and is there a way to condition the fuel somehow to remove condensate and clean out eventual b/s from the carb without major mechanical work (I really don't want to pull the boat ashore before autumn)?

Thank you!

Honda outboard | Answered on Aug 17, 2018 | 691 views

Hi there. The tips are generic and may or may not apply! 1)Does it have points with capacitor? It can be burnt or dirty.2) Check the cable feeding the sparkplug loose or cracked? 3) Remove the wires to your kill switch at the engine and try to start if it starts then with your ohm meter check switch working and wires for breaks or short circuits

Honda outboard | Answered on Feb 07, 2018 | 801 views

Type Honda, the model number of your motor, customer service into your computer search engine. It will being up Honda customer service web sites you can contact and ask for info.

Honda outboard | Answered on May 17, 2016 | 37 views

Not the carbs, not the fuel pumps, maybe the fuel delivery volumes to the carbs by the fuel pumps. A restriction can cause the engine to suck the carburators fuel bowls dry if not enough volume of fuel is delivered. Do a fuel volume test

Honda outboard | Answered on May 09, 2015 | 103 views

i would look for a leak in a fuel line or connection or a needle that is stuck open flooding that carb which will sometimes run out of the front of the carb and into the base of the cover. when the air intake cover is on you cant see this happen.

Honda outboard | Answered on May 30, 2010 | 251 views

If you need more support, we recommend you a support website, you can search your answer on the website:

Honda Electrical... | Answered on Oct 15, 2019 | 15 views

If you need more support, please visit

Honda Electrical... | Answered on Oct 10, 2019 | 25 views

For your question, i have replied many people, why generator set can start but not generate electricity?
Here is some reasons for reference:
1.After the diesel generator is stopped, the residual magnetism is often lost, because the material used for the magnetic pole of the exciter is close to the soft steel, and the residual magnetism is small. After the shutdown, when there is no current in the excitation winding, the magnetic field will disappear.
2.The magnetic pole of the diesel generator loses its magnetic properties.
3.Damage of excitation circuit components or circuit breakage, short circuit or grounding phenomena.
4.The exciter brush is not in good contact with the commutator and pressure of brush holder is insufficient.
5.Excitation winding wiring error, opposite polarity.
6.Stator winding and rotor winding of generator set open circuit.
7.Poor contact between diesel generator brush and slip ring, or insufficient brush pressure.
8.Diesel generator lead wire wiring is loose or switch contact is poor.
9.The fuse box is fused.
10.The "auto-manual-de-excitation" switch on the control panel is in the de-excitation position (automatic generator set has "auto-manual-de-excitation" switch).
11.The voltmeter is damaged.
12.Rotary rectifier module is damaged.

Honda Electrical... | Answered on Oct 09, 2019 | 29 views

Most of the time it is either the Capacitor or AVR that has blown (depending on what is fitted on your generator.). Check out our videos on how to test them.
We hold a full range of Generator AVRs and Capacitors.

We have a whole Help Center and Engineers dedicated to helping people fix their Portable Generators. In addition to this we have a "Parts Search Service" if the part is not listed on our site. Check us out on our site.
Parts Spares for Generators and Small Engine Machinery


Honda Electrical... | Answered on Aug 19, 2019 | 75 views

I think there is overload .kindly measure ur load of consumption. Do not run the generator set with high load it can be cause of circuit breaker Tripp off .

Honda Electrical... | Answered on Jul 27, 2019 | 82 views

you probably have either a bad capacitor or more likely a short stator winding due to previous overloading

Honda Electrical... | Answered on Jun 03, 2019 | 88 views

Verify that the double gang circuit breaker is good on both sides. Check for loose wire on breaker or receptacle.

Honda Electrical... | Answered on Jun 03, 2019 | 137 views


We have a put together a guide here to assist you in these situations. It will guide you through testing and repairing the Generator. :
If you need any further help our Generator Engineers are happy to assist you.

Regards,The Generator Guru Team
Parts Spares for Generators and Small Engine Machinery

Honda Electrical... | Answered on May 31, 2019 | 65 views

use your car battery and jump it. you cannot get too big a battery. big is better.

Honda Electrical... | Answered on Apr 10, 2019 | 77 views

If it's on a Ryobi Generator then it should be a real Honda Engine. It's possible that it's a knock off or was replaced with one. If you bought it new from a reputable source then it's real, if it's used or came from an offshore source for a really low price then it's a good possibility that it's a kkoxk off. In all honesty, from my experience they do a great job with the knock off engines & they're usually reliable and last a normal life span similar to a real name brand.

Either way, that mechanical Issue Remains, I'm assuming you're refering to the valve being stuck and basically keeping the engine locked up and not allowing it to the over when attempting to start it. Sounds likely. Did you take the spark plug out and turn it over to see if it'll turn over at all to ensure it's not just totally locked up? My suggestion would be to Remove the valve cover and spark plug so that you can see the valvetrain in action when(if so) it is turning over and observe it to see if your valve theory is correct!

Thanks and good luck my friend, see the infinity below please, have a great day!

Honda Electrical... | Answered on Mar 18, 2019 | 66 views

Not finding what you are looking for?
Honda outboard Logo

10 questions posted

Ask a Question

Usually answered in minutes!

Top Honda Electrical Supplies Experts

John Trevino

Level 3 Expert

1420 Answers

Norman Al-Anbar

Level 3 Expert

630 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Are you a Honda Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides