20 Most Recent Honda outboard - Page 9 Questions & Answers

0helpful
1answer

Where is 10A fuse holder on honda ex5500 generator

Usually on the power board under a black grub screw which you should be able to undo by hand.
4/22/2015 9:58:48 PM • Honda Electrical... • Answered on Apr 22, 2015
0helpful
1answer

Honda em7000is generator has no spark what could it be

BEST VIDEO TO SHOW THE PROCEDURE TO TROUBLESHOOT, HOPE IT HELPS... https://www.youtube.com/watch?v=Wi5gTyyHUIU How To Diagnose Repair Generator With No Spark Ignition Module Replacement
3/29/2015 5:26:18 AM • Honda Electrical... • Answered on Mar 29, 2015
0helpful
1answer

Point gap wanted for honda 300u generator

General rule of thumb for point gaps. 25 thou. Hacksaw thickness Should work fine.... it's not a precision machine?
3/6/2015 8:09:40 AM • Honda Electrical... • Answered on Mar 06, 2015
0helpful
1answer

What is the valve clearance on a 1800 watt generator

Use the name plate information on the engine to identify the make and model of the engine. You shuld then be able to look up the engine specs on-line.
3/2/2015 6:40:07 PM • Honda Electrical... • Answered on Mar 02, 2015
0helpful
1answer

Need a Honda eb2500x generator service manual Runs but doesn't produce power circuit breaker is closed

Check if you have power on each leg, l1 and l2 coming off the stator before the breaker. If you have only one leg then the stator is suspevt. if you have zero, check stator resisitance and shorts to ground, rotor the same, and voltage regulator and or capacitor
2/28/2015 11:39:59 PM • Honda Electrical... • Answered on Feb 28, 2015
0helpful
1answer

Alve gap on a Honda GX390 engine? Hi, I have a gas generator with a Honda GX390 engine in it. I need to adjust the valves. Any idea what the gaps are supposed to be? Also do I adjust on a cold engine

GX390K1 Intake 0.15 +/- 0.02mm ( 0.006 +/- 0.001in ) Exhaust 0.20 +/- 0.02mm ( 0.008 +/- 0.001in ) Usually done with the engine cold/
2/24/2015 3:38:47 AM • Honda Electrical... • Answered on Feb 24, 2015
0helpful
1answer

Honda diesel generator surging

does it surge under load ? or without load, if without load it could need the injector cleaning if under load it could be the governor at fault
2/19/2015 1:41:24 AM • Honda Electrical... • Answered on Feb 19, 2015
0helpful
1answer

Honda generator problem error code 04 how to clear

I have a video that may help you to troubleshoot the problem. https://www.youtube.com/watch?v=zGy9WoA537w&list=UUycoCur2JWPEhrS0qTeyIJw Please let me know what you find I am happy to help further. Joe barterjoes.com
1/29/2015 2:34:48 PM • Honda Electrical... • Answered on Jan 29, 2015
0helpful
1answer

How to do a static gov adjustment on a Honda EB3500XK1 generator?

PLace the throttle at full position while watching the governor arm. Loosen the clamp bolt on the governor arm and turn the governor crank in the same direction as previously noted until it stops. Now retighten the clamp bolt.
1/28/2015 5:53:03 PM • Honda Electrical... • Answered on Jan 28, 2015
0helpful
3answers

Brand new gx390 Black Max

If you can access throttle linkage to the carburetor, slow the engine speed to idle before turning off. As mentioned in the previous answer ... turning off the fuel valve and letting it run dry is good if you are not planning to use it real soon.
1/26/2015 5:11:55 AM • Honda Electrical... • Answered on Jan 26, 2015
0helpful
2answers

I have a small Honda

Make sure the fuel valve is on, if that does not fix it you will need to drain the bowl on the bottom of the carb. What model is it
1/26/2015 5:06:21 AM • Honda Electrical... • Answered on Jan 26, 2015
0helpful
1answer

My honda gx390 is starting but not producing electic power

There should be a switch on the unit the turns on the outlets.
1/5/2015 3:35:09 AM • Honda Electrical... • Answered on Jan 05, 2015
0helpful
1answer

Have a B&S VOX 6500 industrial generator with Honda motor. Generation quit and no breakers flipped. voltmeter shows 3.4 volts on both legs when running. What happened? and how do I fix?

It may be just as simple as flashing the fields. Remove the end cap of the generator. Look for the brush holder on the top center of the housing The brushes may be worn out or the fields may have lost the residual magnetism. The brush holder has two wires going to it, a red (positive) and a ?white (negative). Hook a couple of wires to a 12 volts battery. Plug a lamp into the generator that will light up when it begins to charge. BE VERY CAREFUL!!!!! Start the generator and momentarily connect the two wires to the brush holder connections. Make sure you observe the polarity Two or three seconds is plenty. If this doesn't work remove the brush holder and check brushes.
12/21/2014 11:46:49 PM • Honda Electrical... • Answered on Dec 21, 2014
0helpful
1answer

Honda gx400 parts

Honda GX400 either a motor car (which will have a '12V Generator' on board..) or a largish sized Honda utility engine for water pumps, fans and electricity generation of of over 5KW (5KVA)
12/19/2014 7:40:10 PM • Honda Electrical... • Answered on Dec 19, 2014
Not finding what you are looking for?
Honda outboard Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top Honda Electrical Supplies Experts

vince

Level 3 Expert

2530 Answers

Paul Carew

Level 3 Expert

3808 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Honda Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Honda Electrical Supplies

  • Honda Electrical Supplies

Most Popular Question

honda 50bf 2009 takes about 10 minutes

  • Electrical Supplies
Loading...