Top 20 Canon MultiPASS F60 All-In-One InkJet Printer Questions & Answers

Hi. if your multipass is connected to a computer you can check in the printer monitor status the exact error . Or you can count how many time the error display blinks

Part replacement:
- Ink cartridge
- Logic board

Window 7 operatimg system is the latest on the market so expected not to malfucntion. The situation with the recent computers despite being latest innovations in technology is least compartibiluity with prior systems. Consider that, your computer is the most up to date and should not be interfered with older codes from prior operating systems. You may be attempting to connect an older devices requiring codes on the windows 7. However, so far windows 7 is still getting in to the user explorability phase similar with prior operating systems. What this means is that, the more complaints about the operating systems, programers tend to redesign compartibilty hybrids to the sytem if not changed by a better computer altogether. Keep in mind that, if a computer program is not communicating with windows 7, dont mind to much since your computer is in perfect order. likely, the additional program is malfunctioning because is outdate and likely incompartible upgrade with windows 7. Identify the specific incompartibilty program code to be communicated to the microsoft internet site as malfunction would initiate an alternate code to bridge the condition. Also, join an internet computer programmers blog to lay the problem on the table. They would delibrate to invent sofwares observed about the recent windows 7.

1st You download Printer Driver. Canon Multipass Inkjet Printer Driver After this install the Printer driver in the system.
Installation of Printer Driver

• Go to the control panel
• Click on the System Icon
• Click on the Hardware Tab
• Click on the Device Manager then
• Select the Unknown Device or printer device where yellow Question Marks sign on it.
• Right click on it and uninstall it.
• After this go to the top of the device manager and click on scan for hardware changes.
• Driver installation Wizard start.
• Brows Your Driver from the Hard Disk and click on next.
• Driver will be install.

I've checked and you can't. Canon don not spport Win7 with this printer so you will have to replace it.

You should also check any other periferals you have using the Win7 compatability wizard available from Microsoft.

You need to remove the inks and lift out the printhead, check the bottom for any paper scraps, wipe gently on a damp paper towel. If after cleaning you still get partial blue, you will need a new printhead. The part number is stamped on the side of the printhead. Sometimes paper lint and scraps stick to the bottom of the printhead.

The waste ink absorber may be full, may not. But the message comes up on cannon printers after so many hours of use regardless. Just reset it.

STEP 1:- Disconnect printer from AC power
STEP 2:- Press and HOLD the POWER button, and connect printer to AC power
STEP 3:- release the the POWER button
STEP 4:- Press the POWER button again

Hi there

Just take them out and gave the brass connexions a good clean and put back.

All the best Pineworks

Hi

This works on the F30, F60, and F80.
Resetting the Waste Ink Volume Counter
1) Enter SERVICE MODE.---
By pressing Menu-Copy-#
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [OK] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Skip step (6) since there is no [OK] key on F30 printers.
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

If it has a nozzle cleaning option use that.
If that doesn't work try some of that pink cleaning flush you get with refil kits on the nozzles.

I had a case just like yours where the printer wasn't in use for some months because there was a second, better printer to use instead. So when the abandoned one was to be used again, it was no longer salvageable. And I tried cleaning it and maintaining it doing everything in the book to make it work again but no matter what I did, it ended up in the garbage bin after all my wasted time and effort. I'm sorry. I wish I had better news for you but I'm speaking from experience. Yours might be a write-off too in which case you are better off to just buy a better one.

I have to ask this question of you, just to make sure this is not an issue. Are you using a factory new ink cartridge?
Please consider the following:
If you are using a refilled or third party cartridge that may well be your problem. Most manufacturers build logic into their products to prevent the use of “Other Equipment Manufactured” cartridges as well as re-filled cartridges.
They do this to prevent problems from contaminated inks causing problems with print quality or damaging the physical printhead.
If you are using factory new cartridges, then please call the manufacturers Technical Support for assistance with the warranty on the cartridges
Don

Fello there try

This works on the F30, F60, and F80.
Resetting the Waste Ink Volume Counter
1) Enter SERVICE MODE.---
By pressing Menu-Copy-#
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [OK] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Skip step (6) since there is no [OK] key on F30 printers.
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

The installation software only lists the following OS:
Windows 98/Me/2000/XP
Link here.
If you load the software then update the drivers you may have a working printer with windows 7.

Anytime someone updates their OS early it is a risk.
Many components may not work or crash.

If your the type that likes to keep with the newest technology.
Remember there is a reason geeks call this the bleeding edge.

Good luck!
Hope this helps!

Error 5100 is always a carriage error.
first thing to do is check is check the timing strip(plastic strip wide around 1/4 inches and usually located behind the print head)
Make sure there is nothing around it like piece of paper or staple or pen/pencil etc.
Make sure the strip is moving freely and hasnt come out of the roller.

Check VERY thoroughly for any obstruction at all, a very small piece of paper can cause the problem.

I don't speak English very well, i'm trying to xplain what's happening with my printer...
I have a Canon Multi PASS F10, and now i buy a laptop and it is Windows 7, i don't know how to make it works, please help!!!

Hi

This works on the F30, F60, and F80.
Resetting the Waste Ink Volume Counter
1) Enter SERVICE MODE.---
By pressing Menu-Copy-#
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [OK] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Skip step (6) since there is no [OK] key on F30 printers.
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Solved: Printer Will Not Work Tip: Click here to scan for System Errors and Optimize PC performance .... i will try that but now i have another problem. i know what i am typing ... the restore, nothing happens for minutes. i end up closing it. ... I then opened a Word Doc, and when I clicked print, ...
forums.techguy.org

My canon c530 multipass fax machine has the alarm light blinking and wont fax anything. can anyone please help me?