20 Most Recent Canon PIXMA iP2000 InkJet Printer - Page 8 Questions & Answers

Hello there try see if this will work

Reset ip2000
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Hi there try see if this will work

Reset ip2000
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Reset ip2000 / 3000
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

I have to ask this question of you, just to make sure this is not an issue. Are you using a factory new ink cartridge?
Please consider the following:
If you are using a refilled or third party cartridge that may well be your problem. Most manufacturers build logic into their products to prevent the use of “Other Equipment Manufactured” cartridges as well as re-filled cartridges.
They do this to prevent problems from contaminated inks causing problems with print quality or damaging the physical printhead.
If you are using factory new cartridges, then please call the manufacturers Technical Support for assistance with the warranty on the cartridges
Don

Hi there it can be done yes.

But it is a messy job you got to get inside the printer clean all out and put some new pads inside then you need to reset it with the codes.
If you not want to do this yet try this.

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

How To Reset Waste Ink Canon Pixma MP450
OK try see if this will do
Hi there
You can try to reset the cartages this may do it Please call back let us know if it worked for you, PLEASE.


Power off printer
Hold down STOP/RESET button then Press and Hold down Power button
Keep Power button down and Release STOP/RESET button
Release power button
Push STOP/RESET button twice
Wait 20-30 seconds - our LED showed Idle
Push STOP/RESET button four times
Push Power button twice
Power off
Next time the printer is started the waste count will have been reset.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Hi
You can try this it may work I got it of the web,

PIXMA 2000 waste ink counter reset:
Service Mode Operations
1) With the printer powered off, hold down the resume button and press the power button.
2) While holding down the power button, release the resume button and press the resume button twice in succession. Now release the power button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the resume button the specified number of times.

Press Resume Indicator Functions
4 times Green Waste ink counter resetting.

Hope it works for you.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.

All The Best: Pineworks

Before you junk the printer. I would try a new OEM cartridge to clear the nozzles (at least run the deep cleaning procedure 3x). Sometimes the nozzles really get gummed up and the only way to clear them is to use a new OEM cartridge to clean them. For some reason, the aftermarket cartridges do not work in cleaning the gummed nozzles.
If the new OEM cartridge trick works, I would be aware of aftermarket and refilled cartridges since they may vary in quality control. I've used LDproducts.com for my aftermarket Canon cartridge supplier for over 3 years without problems.
Let me know if this helps.

It's indicating that there is still paper under the platen roller inside, or the sensor flag was bent or broken by pulling out the jammed paper.

The absorber covers the entire bottom of the printer. You need to remove all covers and then the print engine. The error code can only be reset in the service mode by a canon tech. Cleaning the pad doesn't help.

Time to look for a new printer, Canon has no parts for this model, it was only exchanged for a new printer during the warranty period and after the warranty expires you toss it when it breaks.

Thru the service mode the error can be reset, but this is a disposable printer that Canon has no parts for, so you can't get the right absorber pad for it. If you reset the count there's a good chance ink will overflow in the near future. Canon only replaced the whole printer during the warranty period and after that it's new printer time.

It remove only OEM software.Search www.canon service tools.com.

where is the Wsare ink absorber located on a pixma 2000

Usually means theres a paper jam or your out of paper or some problem is occurring. While that blinking orange is blinking press and hold it for about 5 seconds the printer should stop blinking orange and continue with the print. Also open up your printer to see if there are any documents that are in the print queue. Probably can delete those. Thats my guess as to whats wrong with the printer. Used to have one of those. Nice little printer remember 12 blacks for 12 bucks.

Issue: Alarm / Power light flashes orange 8 times consecutively (Waste Ink Nearly Full Error)
Solution: Press the <RESUME/CANCEL> button to clear the error (1700)
Waste ink absorber error 1700
The printer has a built-in waste ink absorber to hold the ink used during print head cleaning. Eight flashes indicates that this absorber is nearly full.

Press the <RESUME/CANCEL> button on the printer to clear the error, so you can continue the print job. The printer will need to be serviced as soon as possible.

Issue: Alarm / Power light flashes orange 8 times consecutively (Waste Ink Nearly Full Error)
Solution: Press the <RESUME/CANCEL> button to clear the error (1700)
Waste ink absorber error 1700
The printer has a built-in waste ink absorber to hold the ink used during print head cleaning. Eight flashes indicates that this absorber is nearly full.

Press the <RESUME/CANCEL> button on the printer to clear the error, so you can continue the print job. The printer will need to be serviced as soon as possible.

Yes, any "new" computer should be compatible with any "current" printer -- it would be foolish for eMachines to _NOT_ accomodate all printers.

the printer heads are blocked. try to use the head cleaning function on the printer driver. you will find that it will start to improve after a few cleans. you may have to repeat it about 10 to 15 times.

if that still does not work. you can try a head cleaner such as this:
http://www.specialistinks.com/cleaning-heads.php

I am having the same problem.........will never buy a Cannon ink jet again !