20 Most Recent Canon PIXMA iP2000 InkJet Printer - Page 4 Questions & Answers

Hi, please get new driver here: www.driversdown.com/
www.nodevice.com/driver/company/Canon/Printer.html
www.usa.canon.com/cusa/office/products/.../hs_1200ts

Jay pmcefv

Hi,

STEP 1:
- Disconnect printer from AC power

STEP 2:
- Press and HOLD the POWER button, and connect printer to AC power

This simple power off procedure worked for me!

Cleaning the absorber was also easy. Power up with the cover open until the head moves to the left side then disconnect the power cord so the head is now positioned away from the pads.
The two pads can be lifted up easily with a pair of sharp tweezers then rinsed in running water. They will become white again and can be blotted with paper napkins then air dried in a warm location. The wells in the rubber holder can be cleaned with cotton swabs before returning the two pads (left side first, then press down the right side).

Assuming it has been working before I expect the electronics have died.

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

jkarmaker,

Have you replaced the inkjet cartridge lately? If so it may not be inserted fully or may be misaligned. If you haven't replaced it the cartridge could still be out of the carriage or misaligned from a bad paper feed. Open the top while the power is on. The cartridges should move to the removal section. Remove the cartridges and reinsert them making sure that they are fully seated. They should click into place when aligned properly. Close the top and try printing. If this was the problem your unit should now be OK. If the unit still has problems I would suggest installing new cartridges. If this does not solve your problem you have a bad control board in the printer. This would not be worth fixing. New units do not cost that much.

Thanks for using FixYa and for the great rating. Please consider a testimonial. Thank you.

hardrocko

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

You need a new printhead

You can download the Canon printer drivers from theirsupport WEB site. Please click on this link and select your model printer todownload :-http://www.usa.canon.com/consumer/controller?act=DownloadIndexAct

When you see this message it indicates waste ink absorber is full. The machine uses special pads so it will not leak in and outside the machine. Now you can replace the pads but the machine will need dis-assembly to do this "messy job" and when that is done you must download a utility for your model "if available" to reset the counters so you can print, and finally the carriage must be aligned so it does not swing to far to the left or right because gears will grind. Most service centers suggest replacing the printer at this point.

Pixma IP2000
1. Turn off printer.
2. retaining button Resume/Cancel press button POWER - indicator it will catch fire by green color.
3. let go button Resume/Cancel, continuing to retain POWER.
4. press button Resume/Cancel of 2 times, retaining POWER, after which let go all buttons.
5. when indicator will be lit BY GREEN - press button Resume/Cancel of 4 times!!!
6. turn off printer by button POWER.
It is taken from service manual.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response.

Thanks, Joe I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Hi,

Click on the link below to download the drivers for your printer
Select the operating system to download and start the installation.
Driver Download


* Please rate this solution with Thumbs up and Testimony to help us improve providing support

http://www.google.com/products/catalog?q=PIXMA+iP2000&hl=en&prmd=ivs&resnum=3&wrapid=tlif12897990701361&um=1&ie=UTF-8&cid=651411774020712759&ei=rcXgTMe1HuntnQe7iZH4Dw&sa=X&oi=product_catalog_result&ct=result&resnum=1&ved=0CE4Q8wIwAA#

It seems simple enough, but this is one of the most effective ways of fixing printer cartridge error. Mostly, printer cartridge error occurs when the printer head is unable to identify the cartridge properly. And the basic reason behind this is that the cartridge is improperly attached.

To reattach the cartridge check the following steps :

turn on the lid of the printer and then remove the cartridge from the printer head.

Check the cartridge to make sure that there are no scratches or other damaged parts that can contribute to a printer cartridge error report.

Take note that the cartridge should not be left open for more than 30 minutes; otherwise the ink will start to dry up and the cartridge will get clogged.

Burn it! 110V is the correct.

First empty the tank, Power up with the cover open until the head moves to the left side then disconnect the power cord so the head is now positioned away from the pads.
The two pads can be lifted up easily with a pair of sharp tweezers then rinsed in running water. They will become white again and can be blotted with paper napkins then air dried in a warm location (I used an industrial oven set to 40°C). The wells in the rubber holder can be cleaned with cotton swabs before returning the two pads (left side first, then press down the right side).
then try this to reset:
1 - press resume button and then press power button
2 - release the resume button and press 2 more times then release both
3 - press and release resume 4 times and power 2 times...

Solutions List:

• Ink Absorber Replacement Options iP2000
• Reset the printer

Hi,

You can download the software from manufacturer's support website by clicking this link

On the page which opens, select the operating system of your computer (Windows XP/ Vista..) from the drop-down menu (See attached image).

Then download the required drivers and software.

Please note:

The list of available software and drivers will load only after selecting the operating system of the computer.

Hope this solves your problem. Thanks for using FixYa.