Compaq Presario 4410US (470027-053) PC Desktop - Answered Questions & Fixed issues
Persario will not power up with switch,
IS THAT A Relic CRT monitors/?? wow.NOW THE FULL STORY. (GOT TIME NOW, IM IN MEX,GULF ON A BOAT,WITH SLOW WIFI OR NEAR DEAD.)the PSU is dead if the power button acts deadno fans right ? no sounds, the 2 or 3 fans do not spin and blow1: bad PSU2: or objects plugged into the mobo are shorted,3: mobo dead (Motherboard)do the jump test?here
http://www.pcdied.com/power.html#Jumper
Absolutely no power on presario 4410
Hello there, I am the Expert that will be helping you today. My name is damnor01.
Welcome to
Fixya.
You are experiencing what
referred to in the computer world as a dead computer system.
You either have a dead power supply or a dead computer
mainboard or a dead Processor.
However it may also be a short circuit some where in your computer system.
However see my published guide entitled,
My Computer is not turning on!!! Is it dead!!! No POST!!!
Thanks
damnor01
COMPAQ 4410us desk top
this happened to me alot when i would get a virus.......usually bad news.....i had to reinstall windows everytime. but first i would check to make sure the network drivers are the most recent versions.
OMPAQ 700 ous desk top pc will not connect to
in command window try
ipconfig /release
then
ipconfig /renew
to pull a new ip
then try
ping www.google.com
to check if you can resolve hostnames
also try
ipconfig /flushdns
to clear old dns entries.
can also try disabling unused internet adapters, in case there's a conflict
Compaq Presario 4410US Memory Upgrade Problem
Hi,
In some instances your PC may not be properly recognizing one or more
memory modules. Because you've recently installed new memory, check to be
sure it's properly seated in its socket and the module is compatible
with your system.
If the module is properly secured and
appears to be compatible with your system, remove the RAM and try cleaning the pins using
rubbing alcohol and a cotton swab. Clean each socket on the
motherboard, as well with a soft, clean, dry paintbrush and then blow the remaining dust out.
If problems persist, try changing the
order of your memory modules. DIMM sockets on the motherboard are
labeled (DIMM0, DIMM1, etc). You should always start installing memory
in the lowest numbered socket available. In many cases, the BIOS will
probe the memory module in DIMM0 and address all memory according to
the specifications of the module in DIMM0. If you've installed faster
memory in DIMM0, the system may not be able to communicate with slower
modules in other slots. Placing a slower module in DIMM0 may fix your
problems; however, the faster modules will then, of course, run at a
slower speed).
Hope this helps.
Out of frequency range set lower resolution
reboot the system by pressing F8 if your using windows OS and select last good configuration.
you can try also selecting Enable VGA mode (press F8 while rebooting and select ENABLE VGA mode).
hope this helps, please rate.
I want to install xp on compaq nx 6310 give the procedure with pendrive
2006 PC (HP.coM) 16 years old.. ouch.
XP (microsoft) is now a horrible virus magnet, and there is ZERO support now, are you using the last XP earth 2020???
gee google that. 2001 to 2007 was XP rein , vista 2007
I bet there are 1millons of web site still with XP usage .(old topics)
google them. but Microsoft purged theirs.
it is not sold at all, so how in the world can you get the installer on any pen drive, and XP installed from CD not pen..
worst of all XP installer, can not us 99% of all USB ports and then only half after the install (unless you force them via F6 and floppy drive with xp drivers on the floppy for THIS PC)
to use any relic PCs run LINUX> not XP
Not finding what you are looking for?