American Standard 3701001.020 toilet bowl, back outlit,pressure assist - Answered Questions & Fixed issues

This could be caused by a faulty relay or switch in the control panel. It is best to have a qualified technician inspect the control panel and replace any faulty components. If the issue persists after replacing the faulty components, then it could be a wiring issue and a qualified electrician should be consulted.

To make the water level higher in the pan, the outlet pipe must be higher.

Adjust the float on the fill valve

Depends how old your toilet is, it may be a calcium build up problem on your little inlet pipe inside your tank, but first check your water shut off valve on left side of your toilet near the wall....It may not be open all the way OR the valve has an issue...

Hey, One thing is that maybe there might be some loose plastic shavings in the fill line. From the Factory? or maybe was inside the water line going to the toilet when you connected the line to toilet. Shut off the water and get some towels and something to catch the water and disconnect it from the toilet and use bowl or what ever to catch the water and slowly turn it on and see if anything comes out. Maybe if it is in the line inside the toilet it might fall out by lightly tapping on the fill line inside the toilet to help it fall out. Just a thought when you said it "Sings" that sounds like trash inside the line going to the filler tube and bowl, hey try it who knows it might work. Okay

Hi, First, carefully remove your tank lid, and place it where it won't break or fall. Look for a four-digit number located on the back of the tank, near the water level mark. This is your tank model number. If the number starts with a two, it is a one-piece toilet. Then....visit this link: https://www.americanstandard-us.com/parts-support/faqs/toilets Good Luck!

water level to low or drain partial clog

More likely the sensor has malfunctioned.

these are called phantom flushes. the water is slowly leaking around flapper or the is a scratch of the flapper seat. I use fluidmaster parts

Toilets wear out from mineral deposits. Fixn may cost more then new. Googl used commodes first

air bound or pump overheating

Water turned off or fill valve bad.

https://www.americanstandard-us.com/-/media/sites/asus/files/product-specs/bulk/specsheet5023100.pdf?la=en

I think it's not a wise decision to clean a toilet fill valve, rather than buy a new toilet fill valve and replace with the old one. Thanks.

no reset on motor ( that would not cause breaker to trip, suspect heating element, or motor is bad.

How to Change Toilet Seat This Old House

Company web site - fill in zip code - https://www.americanstandard-us.com/parts-support/where-to-buy/product?productid=c76e85c8-571d-4992-bfd0-7d873c149285 Online retailers such as Amazon.com https://www.americanstandard-us.com/parts-support/where-to-buy/online-retailer/preferred

Yes you can replace the handles as they are available from American Standard, directly. Go to their web site, parts and service, and select you mod. toilet. Order from them. https://www.americanstandard us.com/bathroom/toilets-category

First, make sure the water feed to the tank is wide open, then make sure you have the inner workings set at maximum water level.

Hey. Not sure what model you have, but I assume you're trying to light the pilot. Remove the metal outer and inner (if applicable) cover(s) located at the bottom below the control box. with a flashlight, you should be able to locate the "thermocoupler" -that's a very thin metal tube about the thickness of cooked spaghetti. It should come from the controller and bend around a little until it ends in mid-air. That's where the pilot flame will first appear when you light it, and it should be always on, or else you will need to follow the instructions on the outside of the heater to do so. BTW: while the pilot should always be lit, the main flame (which heats the water) will only "fire" like a gas cooking range when the water in the tank starts to get cold - so don't expect to see any big flames any time you look. When you re-light the pilot, though, and turn the control dial to "hot", then you will both see and hear the flame fire up. Follow those lighting instructions VERY carefully, or the pilot won't stay lit (like, if it says to hold a button for 60 seconds, make sure you don't cheat). Good luck, hope I answered your question.