Top 20 Dell A960 All-In-One InkJet Printer Questions & Answers

AbdelRhman Hashem, You can click the link below to download the online users manual for information on the automatic feeder. For information on creating a PDF you may need to refer to the PDF program help file or user manual. http://dell.to/1PuLpFK Thank You, Dell-Jesse L Dell Social Media and Communities

Q-tips and alcohol clean surface of cartridge and the well it sits in. Youtube may have video on this.

Try unplugging for a little while to reset. Also see if there is a power button. Press and hold

A lot of inkjet printer manufacturers make you purchase their ink cartridges by installing a chip in the cartridges so when the cartridge is empty it cannot be reused by filling the cartridge.

use isopropyl or" petrol & last time some heating.

Here is the Manual for the printer Product Support Dell US You need to set up the printer as on page 49 to automatically print faxes.

Hi Susan,Please note that your printer cannot receive soft copy faxes,it can only send them.Click here for the manual downloads in pdf format.Hope this helps.Thanks!

You can download the drivers from here.Make sure the right Operating System (e.g.: windows xp) is selected, and then click on download next to the "Dell - Driver".

If not even the test page works then it's a hardware problem with the printing heads. In that case the there is only one thing left to try: put some new cartridges in and see if they work: if they don't then the fault is either in the connection between the cartridge carrier and the mainboard (with the thin flat cable on the side) or with the processor on the mainboard.
You will have to dismantle the printer completely and check the cable for damage and reseat it; then look at the mainboard for signs of damage - use this opportunity to do a full cleanup. If even after this the printer is still not working then the processor on the mainboard is defective - the printer is dead, time for a new one.

If this problem occurs with scanned images/documents then the scanning light detector is faulty.

1. If you plugged in your A960 in the USB slot hoping windows 7 would provide the right driver via windows update: Just remove the printer in control panel > printer > rightclick the printer > remove device.

2. No need to use the dell cleanup utility. No need to uninstall under "uninstall software" since it wouldn't show there if the wrong driver was installed by windows automatically (but if you installed a wrong driver manually you may have to).

3. Download the Vista 64-bit Driver R153052.exe (or 32 bit if applicable), links see PudgyOne's post 28 Nov 2009 10:32PM.

4. Install the driver: clicking the R153052.exe first extracts the files to e. g. C:\dell\drivers\R153052. Then rightclick the setup.exe in that folder and change compatibility to Windows Vista Service Pack 2.

You don't need to purchase it, you can download the installer/driver from Dell official website. Click this LINK, the download page for Dell Printer A960 will open up, select your Operating System from the "Operating System" box, eg. Windows xp, wait for few seconds, all the available download, click the download "Download" button beside the driver's name, a new dialog box will pop up, again click "Download" button below the "Download via your internet browser", download will begin automatically. If you are asked to agree the Dell terms conditions, click "Accept" or "Agree".
Let me know if you need further help.
Good Luck
Thanks for using FixYa.
Note: There is no driver for Windows 7 for this model, let me know if you have problem with that also.

The problem is simple. The Shiny Silver bar that your Print Cartridges glide back and forth on is the PROBLEM!!! When the motor that moves the cartridges left and right HAVE TOO MUCH RESISTANCE, YOU GET THE HARDWARE ERROR: 502. How I fixed it is simple. Take some kleenex, and with power unplugged, clean the bar very well. Then Spray some WD-40 on a Kleenex, and lubricate the shaft!! After I did this, I could use my DelL A960 as if it were BRAND NEW!!! Hope this helps some one out there, as I had to figure it out myself!! Take care.
Rob
Please rate.

Sometimes you need to clean the rollers that pull the paper through the printer. There could be a piece of paper torn off stuck back there that causes any paper going through to jam.

Also, make sure the paper sits tightly in the feeder tray but not so tight that it bows.

Try it in Safe Mode- this will be ugly since it's in 16 colors, but if the streak goes away it may indicate an issue with your video driver. If it does not go away, check your target output device setting (is it the printer, the screen, or a device you don't have) and change it to another output device to see if it goes away.

Try updating the list of applications to send scans to.

Update list of applications to send scans to


Rick

Hi and Welcome to Fixya

Connect the printer to your computer via USB cable and download the drivers to this site. You can use the Vista driver since windows 7 and vista are almost the same platform.

Please reply to this email for any update.

Have a good one!

try to print from documents like workpad. if that works, open the file menu or page menu of your browser and look for the Encoding option. if auto-select has a check mark with it, click it once to uncheck it and try fo print again. if that does not work, reinstall your printer driver, set it as your default printer and try to print using another browser. hope it helps

Hi,

Remove the cartridges and clean the contacts ( electrical contacts - golden colored ) with a lint free cloth and re-install them back in the printer.

Try this and check if it prints the test page.

Regards,
Shawn