Top 20
Konica Minolta Bizhub Press C6000 Copier - Page 2 Questions & Answers
Error c6704
Scanner image
processing board
(SCIPB)
• Memory control board /1
(MCB1)
• Overall control board
(OACB)
• Printer control board
(PRCB)
any one of the above boards$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ have tech come reflash the firmware first Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Konica minolta continuous printing
Have you had the developers and drums replaced or does the screen say Replace PC Drums? There are certain house chores the copier does before "Ready to Copy" it is waiting for them to get done, so that equals "Please Wait". One big item is making sure the developer and toner are properly mixed inside the developing units next to the drums. Did you recently replace the drums and the developer if so did you clear the counters for the drums and developer, FIRST? IF not then the copier thinks the new drum and new developer are old. The copier works on the counters that is how it knows it got a new drum and developer. Get new developers and a new drums and have it installed correctly. Counters are clear before the unit is yanked out of the machine, then you remove the drums unit replace the developer. (DO NOT USE A VACUUM CLEANER WHEN REPLACING THE DEVELOPER static electricity can destroy the sensor located below the developer unit. . Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
The printer says controller not connected
Check the cable connections between the printer and controller.Restart the printer. If that does not work then turn the printer off and restart the controller then turn the printer on.
Konica code C-C101
Well possible two items the code is for the paper feed motor either you have problem with a paper issue or more likely the WASTE TONER issue since the Paper Feed Motor (M-41) handles to jobs running the paper feed system and waste toner system might harden old toner in a tube section preventing the motor from turning get a tech out to check the entire waste toner system and or paper feed issue Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Hi
I need a help i hav error code C-8003 on konica Minolta B951. Please assist.
Thanks
Podtermistor wa?ka utrwalaj?cego nie
wykrywa wymaganej temperatury w ci?gu 30 sekund.
po rozpocz?ciu cyklu rozgrzewania; dlatego
kopiarka nie ko?czy cyklu nagrzewania.
• Temperatura wa?k?w utrwalaj?cych nie
osi?ga wymaganego poziomu nawet po
up?ywie ustawionego czasu podczas cyklu nagrzewania.
1
Sprawd?, czy lampka utrwalacza H1 zapala si?, gdy g??wny
wy??cznik zasilania jest ustawiony w pozycji W?., w razie potrzeby popraw lub wymie?.
- -
2
Sprawd?, czy H2 w??cza si?, gdy g??wny
wy??cznik zasilania jest ustawiony w pozycji ON, i w razie potrzeby popraw lub wymie?.
- -
3
Sprawd? instalacj? TH1 i TH2 i
w razie potrzeby popraw lub wyczy??.
- -
4
Sprawd? dzia?anie TH1.
Usu? CN80 (4P), a nast?pnie sprawd?, czy rezystancja
na CN80-2 i -3 na termistorze jest
niesko?czona.
- -
5
Sprawd? dzia?anie TH2.
Usu? CN81 (4P), a nast?pnie sprawd?, czy rezystancja
mi?dzy CN81-2 i -3 na termistorze jest
niesko?czona.
- -
6
Sprawd? ci?g?o?? H1.
W razie potrzeby popraw lub wymie?.
- -
7
Sprawd? ci?g?o?? H2.
W razie potrzeby popraw lub wymie?.
- -
8 Zmie? PU1 - -
9 Zmie? PWB-A
Not finding what you are looking for?