Top 20 Konica Minolta Bizhub Press C6000 Copier Questions & Answers


service mode then clear the counters, should have done it before installing the drums.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | 168 views | 0 helpful votes


check magenta Charge grid.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | 231 views | 0 helpful votes


If you wish to get some details; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/

Konica Minolta... | 384 views | 0 helpful votes


The proper value cannot be figured out within the specified time by the correction of the patch density correction /K. Or, the proper value of the developing DC output is 0 or lower.

Associated Parts:
• Printer control board
(PRCB)
• Developing unit /K
• IDC sensor (IDCS)
• IDC shutter solenoid
(SD3)

Remove the black (K) Drum. behind and toward the front is a silver/chrome looking thin bar with a tine square that square is a sensor clean it or replace the drum (switch different color see if changes codes) or switch out sensor with a different one each drum has one when was the last developer was replaced for black getting close to a PM???

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | 874 views | 0 helpful votes


Flash the latest firmware first and, if that doesn't solve it, to replace the MCB. Flashing the firmware has worked well for other users with the same problem.

Konica Minolta... | 290 views | 0 helpful votes


I think that is the code for the black charger unit. It might be the charger itself or a board problem. Make sure the black charger is seated correctly.

Konica Minolta... | 465 views | 0 helpful votes


Could not locate that code in the service manual, sure about it?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | 1,054 views | 0 helpful votes


Subject:
C-2702 and/or C-2703 code.
Description:
C-2702 and/or C-2703 code.
Solution:

PROBABLE CAUSES:
1. Failed T/S corona.
Remove the T/S corona unit. If blank copies can be printed without a service code appearing, replace the T/S corona unit (p/n 57AA R715 00).

2. The HV unit has failed.
Replace the HV unit (p/n 56AA 8401 2).

Konica Minolta... | 319 views | 0 helpful votes


Check the Cyan Charge Corona housing. Remove it and reseat it. IF not that check the HV board. and or connection at the back of the drum and transfer middle assy.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | 123 views | 0 helpful votes


Did you made all the steps from the service manual when you changed the drums and developers?

Konica Minolta... | 415 views | 0 helpful votes


Main body: Writing correction drive abnormality

Cause> The tilt correction home sensor /M (PS71) turns OFF while the tilt correction motor /M (M75) in the writing unit is ON.

Estimated abnormal parts> • Printer control board (PRCB) • Writing unit

Konica Minolta... | 713 views | 0 helpful votes


Check that all of the charge wire assy.'s are properly pushed in all the way in particular the cyan also ensure that the bolt at the top of the middle section is tight not just the one on the left side when closing the upper middle section housing drums and transfer belt.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | 225 views | 0 helpful votes


Magenta drum sensor is bad, or the magenta drum. Remove the drum and behind it will see a silver/chrome 1/4" near the front with very small square hole, inside that hole is a sensor that reads the drum density for that color, But first clean the sensor with a clean brush!

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | 392 views | 0 helpful votes


What is the error code C-XXXX or SC-XXXX or Jxx-xx what was it doing when it happened?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | 326 views | 0 helpful votes


Replenish toner unit is the unit that is secured with two screws and comes to the right and these are unscrewed. The presence of this unit is signaled by a sensor positioned under the top cover. Check that sensor for proper functionality in Service Mode.

Konica Minolta... | 324 views | 0 helpful votes


check the yellow developer might require developer replacement and or the sensor last PM??????????????????

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | 366 views | 0 helpful votes


It might be the sequence you powered up. Turnoff the main power switch in the body amd the controller power. Restart the controller, this will take a few minutes, then restart the printer. Also check cables between the controler and the printer.

If you have Vcare (the service the communicates various conditions and usage data to KM), then unplug that cable, you might need your service tech to reset something. Your printer will work without the connection

Hope this helps

Konica Minolta... | 484 views | 0 helpful votes


Main body: High
voltage unit /2
abnormality
C-2721 An error detection signal of
the separation charger is
detected while the
separation charger is ON.
The signal is detected
even after turning OFF/ON
for a prescribed time.•
High voltage unit /2
(HV2)
• Separation charger
• Printer control board
(PRCB)

Konica Minolta... | 198 views | 0 helpful votes

Not finding what you are looking for?
Konica Minolta Bizhub Press C6000 Copier Logo

Popular Tags

53 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Konica Minolta Office Equipment & Supplies

  • Konica Minolta Office Equipment & Supplies

Most Popular Question

please set replenish toner unit

  • Office Equipment & Supplies
Loading...