Top 20 Konica Minolta Bizhub C552 Copier Questions & Answers

Have you changed the fusing unit? If try that first, then relace the IH Power supply or the (coil unit) is what the fuser attaches to when you install one. power supply is located right side under the control panel, . Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Hey jrf, the manual says to check, in this order; proper fuser installation, proper closure ( door latch ) of the right hand door, check around-all around-for wiring connection issues, change fuser, then coil, then IHPU, then PRCB, then REDB. If you have a trade-in, or lease return, at the shop; it might pay to do some parts borrowing.

behind the right side cover under the control panel Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

The IH power supply is located below the operational panel behind the front cover below the op panel, Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Located under the control panel. Right side front cover. looks like a power supply. connects to the fuser, Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Replace the IH Power supply, it will solve your problem... Page 71 Item 5 from the parts manual.

again please explain? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Because there is a problem with tray four so it makes it disappear First open tray four remove the paper that might be stuck behind it.. Then enter service mode utility/counter, touch details on the meter count, then stop 00 stop 01 then select system 1, then select problem unit isolation, then select tray 4 your going to unset follow the screen, then your going to do the same process again this time set, if the draw continues to not show after this procedure get a tech out to look at it, as for tray three maybe the rollers need replacing have the tech look at them to. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Black drum ATDC replace the black developer unit, also check to make sure the black toner is getting into the black developer unit. Open close the front door to reset the code (Not the Toner door) Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

English only on Fixya please. We are a North American website.

Error Code Pls help - Konica Minolta

Copytechnet https://www.copytechnet.com > ... > Konica Minolta Jun 20, 2012 - CD252 (C-D252) code at start up. Solution CAUSE: The Controller 1 setting is enabled in Tech. Rep. Mode without the IC-409 (Fiery® ... fuser error code C252 May 7, 2014 Bizhub C451 bad print quality, no accurate color Jun 4, 2014 Error Code Bizhub 283 with C-D272 Mar 17, 2016 error code C- D251 bizhub C451 May 19, 2009 More results from www.copytechnet.com

Konica-Minolta bizhub C452 - Error Code

Printcopy.info https://printcopy.info > model=bizhub+C452 Code: CD252; Description: No relay circuit boards for IC-412 mounting at IC-412 mount setting; Causes: MFP board (MFPB) Relay circuit boards (VI-505) . ..

Help in the links

Konica - Mini Lab Help Forums

Mini Lab Help https://www.minilabhelp.com > forum > 19-konica Mar 7, 2021 - Error code R2. Cpu Board R2 Super - Konica - Mini Lab Help Forums Dec 15, 2014 konica r2 super 700 error (d1301) - Mini Lab Help Sep 9, 2020 Konica - Page 3 - Mini Lab Help Forums Mar 7, 2021 Konica Minolta R2 Super 700 processor problem Nov 28, 2023 More results from www.minilabhelp.com

Aboo - Mini Lab Help Forums

Mini Lab Help https://www.minilabhelp.com > profile > 12347-aboo Aboo started following Cpu Board R2 Super , Error code R2 and Printer Head December 4, 2023 ... Error code D1301 Link with the processor faild. May 14, 2021 · 22 ... https://www.google.com/search?q=Konica+Minolta+R2+Super+Error+code+D1301 ..

Question edited for a lot more clarity and add maker. Question moved to maker category. Cooling Fan failure.

Konica-Minolta Di2510 - Error Code

Printcopy.info https://printcopy.info > model=Di2510 > code=C0045 Code: C0045; Description: Cooling Fan Failure • The Cooling Fan Motor Lock signal remains set to H for a set period of time while the Cooling Fan Motor is ... Missing: dialta ‎' Show results with: dialta

Error Codes > Konica-Minolta > Di2510 > page 1

Printcopy.info https://printcopy.info > model=Di2510 Code: C0045 · Description: Cooling Fan Failure The Cooling Fan Motor Lock signal remains set to H for a set period of time while the Cooling Fan Motor is ...

Usually this happens when machine is operated in environment that does not fulfill the recommended environment i.e. temperature and humidity. Similarly, if toner cartridge is refilled with toner that does not match the category which is recommended, lighter print are observed. If toner is about to end, same also happens. See the environment conditions in the manual and replace toner cartridge with genuine cartridge. Operation Precautions; Power Source; Operating Environment; Storage Of Copies - Konica Minolta bizhub 367 Quick Start Manual [Page 28] ' ManualsLib

What is error code c2557 on Konica c220? Check the toner bottle to ensure that it is feeding toner into the sub hopper unit under the bottle. Sometimes users will insert the bottle incorrectly and not lock it properly in place...the lever on the front of the toner hopper for that bottle is moved down to the left to remove and insert the bottle. Dec 28, 2010

Error code C2557 - Konica Minolta - Copytechnet

All in the link. You can't Scan FROM a USB drive because if it was on the USB Drive it is already in digital format. You can Scan TO a USB Drive. For the faint text, remove the toner cartridge and give it a couple of hard taps on the either end to settle the toner. Then run a Test Page https://www.google.com/search?q=Minolta+Bizhub+220+scan+or+print+from+flash+drive ..

You can try it, but the manual says 10 at a time via the Bypass tray. The problem is the fact that normal paper from the trays takes a rather tortuous route through the machine that contains sharp turns. By far the easiest way to print a lot of envelopes is to use Avery 8163 Labels. Use the Avery template and create the pages of addresses and print 50 at a time from the normal paper tray. https://www.google.com/search?q=Konica+Minolta+Bizhub+880+print+9+x+12+envelopes

Template for Avery 8163 Shipping Labels 2" x 4"

Avery https://www.avery.com > templates > 8163 Avery® Erasable Multi-Use Removable Labels, 7/8" x 2-7/8", W... ... Avery® Printable Tags with Sure Feed, 2" x 3-1/2", White, 96... ... Avery® Easy Peel® Address ... ..

C454 and C454e firmware - Page 2

Copytechnet https://www.copytechnet.com > ... > Konica Minolta May 4, 2019 - Re: C454 and C454e firmware. Hi there, I hava Konica Minolta Bizhub C454 with ROM Version: b-IZHUB-c454 - imgbb.com C454 and C454e firmware May 5, 2019 UPDATE FIRMWARE ON c454 Jun 19, 2015 Bizhub latest firmware? Mar 10, 2022 Firmware question Jun 19, 2019 More results from www.copytechnet.com

Updating the Firmware of This Machine

Konica Minolta Manuals https://manuals.konicaminolta.eu > contents User's Guide. bizhub C554 C454 C364 C284 C224 ... A firmware for this machine can be downloaded from the Internet to update the machine firmware.

Download Center - KONICA MINOLTA

konicaminolta.ge https://www.konicaminolta.ge > download-centre The download center of Konica Minolta! Find everything from driver to manuals of all of our bizhub or accurio products.

Trouble Code C-6752 Reset on Konica Minolta C220/C280 ...

CORONA TECHNICAL https://www.coronatechnical.com > 2019/07 > trouble-... Jul 12, 2019 - This code means is related to CCD. When starting the scanner, verification of reading and writing the predetermined value for image processing ...

Question edited to add English make and model. Question moved from Cars and Trucks category. English only on Fixya please. We are a North American website. Reset maintenance minolta dialta di152. Cruet of oil. And this is the problem. Copiers have a 'cruet of oil'? And they do! https://www.google.com/search?q=minolta+dialta+di152+oil+tank ..

If you have already replaced the charging corona, developer powder, and cleaned the laser unit, but the problem of a white light appearing on the artwork persists on your Konica Minolta Bizhub C454, here are a few additional steps you can take:

1. Check the transfer belt unit: Ensure that the transfer belt unit is clean and free from any debris or toner particles. You can gently wipe it with a clean, lint-free cloth. If the transfer belt is damaged or worn out, it may need to be replaced.
2. Inspect the imaging unit: Check the imaging unit (drum unit) for any signs of damage or wear. Make sure it is properly installed and securely seated in its designated position. If the imaging unit is defective, replacing it might resolve the issue.
3. Perform a density adjustment: The Bizhub C454 usually has a density adjustment function. You can access this in the device's settings menu or through the control panel. Performing a density adjustment might help improve the print quality and reduce any unwanted artifacts.
4. Check the print settings: Ensure that the print settings on your computer or the printer's control panel are appropriate for the artwork you are printing. Adjust the print quality, resolution, and any color settings as needed.
5. Update the firmware: Visit the Konica Minolta website and check if there are any firmware updates available for your Bizhub C454. Updating the firmware can sometimes address software-related issues that may be causing the white light problem.

If none of these steps resolve the issue, it is recommended to contact Konica Minolta's customer support or a certified technician for further assistance. They will have specialized knowledge and tools to diagnose and fix the specific problem with your machine.