20 Most Recent Epson Stylus CX3200 All-In-One InkJet Printer - Page 4 Questions & Answers

Hi,You cannot actually change the lamp for the scanner. Better get a new one instead. Have a nice day!

سلام من درایور و نرم افزار پرینتر epson stylus cx3200 all in one مدل c151a رو میخوام لطفاُ به ایمیلم بفرستین [email protected]

This is a "General Error" issue, not a service required one.

It's likely that either a sensor in the printer is damaged (possibly a ribbon cable has come detached)... or more likely there is some foreign body or printer part that's come loose and is blocking the printhead carriage path.

A common one I've seen with the C86 and similar is for the head cleaning part become detached from the parking pad (all based far right)... When it does this it springs up into the printheads path and stops it from reaching the parking position.

It requires patience to fix (and some rubber gloves to avoid ink mess) but if notice a part doing an impression of a jack in the box then you can usually gently push the part down and then careful maneuver it over to the right into a connection with the parking pad part.

It's hard to describe without pictures but it gives you an idea of what to look for.

You can download drivers for this printer from this link, just click HERE and proceed with the download.

click this link then select what os are you using then download driver http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=14082&prodoid=24875245&infoType=Downloads&platform=Windows

It is very easy to change ink in your Epson printers. First remove the old cartridges from your printer by following the instructions in your printer user manual. After that, clean the printer with cleaning cartridges. Then do a Nozzle Check and run another cleaning cycle. Repeat the last two steps for several times until only clear fluids get released. Now install the new ink cartridges into the printer and turn it on and start the prime cycle.

After the completion of the prime cycle do a test print. If everything is okay then you know that the printer is again ready for use. It is a very simple procedure but needs concentration and proper care. If you want a more detailed procedure then check it out at www.inkjetart.com. This site has detailed instructions on various Epson printers and matters related to it.

yes, try to print a page and you should get a text box appear at the bottom of your screen telling you your ink is low, click on this box and it will tell you which ink has or is running out

EPSON Stylus CX-3100 Printer Driver for Windows 2000/XP
Download File Name : CX3100_win2000_XP.zip (4.4 MB)

NOTE : epson stylus cx3100 is similar to cx 3200.

Step by step instructions with pictures are here

In most cases the printer driver software can have errors while being in use or is shut down. So to reset remove your printer from the PC and uninstall the printer software. Now reinstall the printer software and then connect the Printer to be detected as a new hardware as it will be installed. Now check the printer properties to see the ink levels.
Activate head cleaning before a test is taken . Sometimes it is possible that the head is not reacting to the need of the PC command or can be an issue with ink drying or poor ink cartridge contacts.

Hi!
Run a Head Cleaning Cycle. If that won't help. chances are the tubes are already blocked with the ink from previous cartridge. You can bring it to a Certified service center but its better getting a new one.
Hope this helps.

hellow i need an adjustment program for epson stylus cx4300 .., anyone can help me plsss.....

can you tell me all the message on the screen?

You need computer and ICnet program if IM not mistaking

The following may work: remove all the ink supplies. Remove the printhead and soak it for about 5 minutes in 0.5" of very hot water. Gently blot the printhead on a soft damp paper towel to remove the excess water, then replace in the printer and then reinstall the ink supplies.

Hi,

Take the cart out and put it back in there might be some loose connection.
The error light flashing is caused by that bad or damaged cartridge. You can always try cleaning the electrical contacts on the cartridge and inside the ink
cartridge holder assembly, with a damp Q-Tip. Then dry the contacts with a new dry Q-Tip and retry the cartridge. If that does not help, and you still have
your old cartridge, try reinstalling it, even if its empty and see if that printer time out problem goes away.If it goes away replace the cartridge.

Hope this helps.

Shan

Hi rswarb,

If your printer won't scan, it might caused by a corrupted driver or application. The easiest way to resolve this issue is to reinstall the driver together with its application. Here are some steps that you can apply on installing the driver.

1. Please click this link. You will be directed to the Epson support site.

2. Select the driver and application that matches your operating system.

3. Now, save them to your dekstop.

4. After downloading, install the driver and application then restart your computer.

5. Connect the printer to your computer then try to run a self test and scan.

Hope it helps.

Thank you for using FixYa.