20 Most Recent Topcon Gpt-8205a Robotic Reflectorless Total Station Questions & Answers


Error. Over Current - Peak current exceeded
Possible causes:
Motor has a short - Phase to phase or phase to ground.
Motor cable damaged/defective.
Motor cables too long.
Acceleration/deceleration ramps too short.
Damaged output phase of inverter.
EMI

Electronics -... | Answered 2 hours ago


Three years is pushing the life of the batteries. Have them checked where your type of battery is sold.

Electronics -... | Answered Yesterday


You can use Card Data Recovery. It is the professional SD card data recovery software. It can recover photos, video, audio and documents from SD card, miniSD card, micro SD card, etc. This program has two versions, one for Windows users, one for Mac users. You can visit its official website to have a look.
Card Data Recovery for Windows
Card Data Recovery for Mac

Electronics -... | Answered 2 days ago


it means you can't write new files or alter the files.
It is cs26466 ?
this has a password protection feature apparently
is it an sd card ? move the tab on the side of it
If it is a usb flash drive I do not know how you get pass the passwor dor how you enter a password when accessing it ?

Electronics -... | Answered on Sep 20, 2019


Write protect in flashdrive could mean chip problem if you cannot partition or reformat the usb drive..you can try usb low level format, partition application..be sure to back up files before doing so.

Electronics -... | Answered on Sep 19, 2019


Connect and get best solution of email related issues. Webmailhelps

Electronics -... | Answered on Aug 30, 2019


When Ally starts chanting "I need my pack", it can become your worst nightmare. I can't find "the pack" but I'm guessing it's the keypad that you plug into her wrist. My bet is the pin/plug connectors in these dolls were not super awesome quality wise and sometimes didn't register they were connected (the program cards were a bit glitchy as well). Once the batteries need replacing, the doll needs to be reprogrammed hence the keypad connection request. Just a guess...

Electronics -... | Answered on Jul 26, 2019


I don't know how new these are, but there is one trick to try to recover a battery. Make sure it discharges completely(will not turn on at all, no matter how hard you try). Then charge it completely. Continue to discharge and recharge, (again, when discharging try again and again to turn it on till it will not come on at all).
This process should start to help the battery get back it's charging 'memory' and you should notice the battery last longer and longer with each charge. If this does not work, there is a problem with the battery. Good luck!

Electronics -... | Answered on Jul 14, 2019


It should have a small 120V to DC wall adapter charger with a DC wire / connector jack that plugs into the back of the power pack. Plug the wall adapter into 120V outlet and plug the DC connector jack into the back of the Power Pack. Leave on charge until the unit indicates it is charged fully (several Hours if it was fully discharged).

Electronics -... | Answered on Jul 14, 2019

Tip

2004 Honda Pilot Left Hand Window Controls.


Just sharing that if you change out the controller arm for the window raise and lower, and you are trying a test run of the new control arm before installation,

YOU WILL NEDD TO MAKE SURE THAT ALL, ELECTRICAL CONNECTIONS ARE HOOKED BACK UP. INCLUDING THE DOOR SAFETY PANEL LIGHT.
( No need for the speaker connection at this point).

If if you have one electrical plug not plugged back into where it came from, you will not get any action from the window motor control arm AT ALL !!!!!!

Hope this helps someone soon. Thanks goes to another user of this sight of open knowledge as he had mentioned it in a reply that I was able to read and add to I hope.

on Jul 06, 2019 | Electronics - Others


These are all messages that follow overheating. E.nOH indicates that the heat sink has returned to the normal temperature range and the unit can be reset. E. OH indicates that the power module is over-temperature. This could be caused by insufficient air flow at the heat sink. That is caused by dust/dirt. The ventilator could be clogged or the ambient temperature is too high. E. OH2 indicates that the motor protection relay was tripped. Check for dust/dirt and clean any filters. Make sure that nothing is blocking the air flow around the unit.

KEB uses these error mesages on the CombiVert F6, https://www.keb.de/fileadmin/media/Manuals/f5/control/f5m/00f5mebk320.pdf .

I hope this helps.

Cindy Wells

Electronics -... | Answered on Jun 01, 2019

Not finding what you are looking for?
Topcon Gpt-8205a Robotic Reflectorless Total Station Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Top Topcon Electronics - Others Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Brad Brown

Level 3 Expert

18108 Answers

Are you a Topcon Electronics - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Topcon Electronics - Others

  • Topcon Electronics - Others

Most Popular Question

leica wild t1010 total station distomat

  • Electronics - Others
Loading...