20 Most Recent HTC Att Vivid Headset Headphones In Ear Earbuds Earphones Earpieces - Page 9 Questions & Answers

It sounds like the internal battery has failed https://www.google.com/search?q=hbs-1100+tone+platinum+headset+replace+battery ..

How To Clone a BPR40 Radio
Cloning duplicates the contents of your radio (master radio) into the new radio (slave radio). Tuning and alignment information are not affected by cloning.

Set Up the Master Radio

1. Turn off the radio.
2. Press and hold Programmable Button 1 (the top programmable button) and turn on the radio. Keep pressing the Programmable Button 1 until beep is heard twice.
3. Release Programmable Button 1. Notice the LED changes to RED

Set Up the Slave Radio
1. Turn off the radio.
2. Press and hold Programmable Button 1(the top programmable button) and turn on the radio. Keep pressing Programmable Button 1 until the beep is heard three times.
3. Release Programmable Button 1. Notice that the LED changes to GREEN

BPR40 Radio to Radio Cloning Procedures
1. Connect the cloning cable to both the Master and Slave radio.
2. Press and release Programmable Button 1 of the Slave radio.
3. Within 2 seconds Press and release Programmable Button 1 of the Master radio.
4. The LED for both radios show flashing orange during cloning.
5. Once cloning is completed, an

I Personally don't think that these should be sold as "safes", but that is a discussion for another thread

Did you get an answer?

GOOGLE LINK BELOW https://www.google.com/search?q=swing+kit+on+my+rci+2980&oq=swing+kit+on+my+rci+2980&aqs=chrome..69i57&sourceid=chrome&ie=UTF-8

443 million suggestions to your mystery question, on your mystery object here. https://www.google.com/search?q=reset+red+light+to+the+blue+one ..

Possibly an open fuse

Did you ever solve this? I have one headset that will not power off. It will not enter pairing mode, either. Curious if you had the same issue and if you fixed it. Thanks.

South African connection issue from meter to supplier.

WBEC AND TAMER METER FAULT FINDING - Ekhwesi Energy

https://ekhwesienergy.co.za > images > forms > 44...

PDF When the power is turned on in terms of a wireless meter the screen should display "SEr" ... the UIU, when correctly paired the screen will display "RF Con" with a "tick". 5. The meter can then ... this means that the tamper latch has not ... If you have signal and the RF CON message on a meter that was previously paired then ...

Please Help With My Conlog Prepaid Meter - Technology ...

https://www.nairaland.com > please-conlog-prepaid-meter

ystar: If the conlog meter is showing rf-Con, it means power supply doesn't reach the meter at all its either Loss of phase from the transformer or a loose contact ...

Prepaid electricity: Wireless Meter ' MyBroadband Forum

https://mybroadband.co.za > forum > threads > prepaid-...

Jan. 22, 2018 · 3 posts · ‎3 authors Asking for a friend, He is using a wireless electrical meter, however on the meter it says: rF con He said it's a conlog, so I googled it and...

Here are all Umeme yaka symbols and their meaning - Dignited

https://www.dignited.com > umeme-yaka-symbols-and-...

Jul. 29, 2015 - The power meter is really easy to understand. However, the meter will also throw some error symbols on the same display which we already ...

IF it works, what are you questioning? It is rare for any antenna to have a flat SWR across the whole band. One has to ask what meter you are using and of course you know that you cannot measure SWR on SSB right?

radio frequency

what do they look like???

If you are streaming music or video, it is the signal cutting out due to Internet connection issues. If it is music from your phone, then it can only be two things 1. the earbuds are too far away from the phone. Try moving the phone closer, or move it to the other side of your body. The receiver is only in one ear bud. 2. they are faulty. Return them under warranty.

scramblepad Mar 08, 2021 Delete Local Police,some fire and Ambulance, Sheriff and State Police have switched to digital mode which this scanner does not have the capabilities of decoding. To check to see if it works grab a family radio and have the scanner in search mode in the 460 mhz band. Start talking or keep the family radio transmitting until the scanner stops on the channel and talk to see if you hear anything. Another very active band is the ham radio band on 2 meters [ 144.000 - 148.000 . Scan that band and I am sure you will get activity. Very active is the APRS [automatic packet reporting system ] frequency of 144.390 which will sound like a bunch of buzzing tones because it is not voice but data and you can decode it. Another active part of the ham band is 146.520 which is the calling frequency. Fire / rescue seem to use both digital and analog, in my area analog is used 70% of the time. Why the weather band does not work is a bad sign. You should be able to get at least 1 channel. Try to search the 162.00 - 163.00 band. If you get nothing you may have a bad antenna,cable or a bad connector or all 3. You can check the antenna cable with a ohm meter to see if their is no shorts or opens. Hope this helped some and let me know how things are. Take care for now, Kevin

Yes and no. You will have to tune your clarifier and you should be able to tune out the loud am signal and hear it unless a person on the am side is 1k or more off. Unless you have a unlocked clarifier. For more information on unlocking it you can go here... https://www.angelfire.com/wv2/whiskeyvictorydx/clarifiermods.html I dont know what model you are using but this will give you some more info. Also, you wont be able to understand side band on am but you can tune in some am stations on side band. Now their is a way to get double side band which is called am side band....i wont get into that but you can view a little about that here.... https://youtu.be/gEB7JEX3wg4

There are Reviews here that show you how to use it. https://www.google.com/search?q=Z9i+bluetooth+headset I wrote this Tip on pairing Bluetooth Devices Pairing Bluetooth Devices Posters often ask "How do I pair my Bluetooth ???" Insert whatever device you have at the question marks. Generally, you need to read the instructions for the camera, headset, speakers or whatever the Bluetooth device is. Roughly speaking though. Settings - Bluetooth - Search, on the Android, iPhone, Windows phone whatever. With camera, speaker, headphones or whatever the Bluetooth device is, you have to press a button on that device to send out the signal. On my Bowers and Wilkins T6 Speakers, there is a button on the top with the Bluetooth symbol on it. This is the part people usually don't do and ask for advice, thinking it will do this automatically. When the Android device recognises it, click Pair, and if it asks for a code, the Default is '0000', (four zeros, no quotes). Posted by ADMIN... on Nov 19, 2016

Contact Tait to inquire.

yes

At $30 it is pretty much a disposable item. It is a shame, because the reviews are good. See is you can find a local electronics hobbyist to look at it. https://www.reallytech.net/catalog/product/view/id/11227/s/auvio-hbt2000w-home-bluetooth-speaker/ Reviews https://www.amazon.com/AUVIO-HBT2000W-Bluetooth-Speaker-White/product-reviews/B00FP2PX28 ..

un-pair device and then re-pair both devices