Nortel BCM50 Main Unit Rls 3.0 - Like New - Page 4 - Answered Questions & Fixed issues

A button may be stuck on the dial pad. Check all buttons to ensure they are free and none of them are stuck.

This is tech side programming known as Configuration, clients usually call in a tech/vendor for this.You need to find out the password and know how to navigate the system programming, do F**266344 and enter the password.Navigate to Sets, add line in question , assign ring type.

You should call in your local vendor and have this done.They will need to install a jack that matches your headphone jack and punch it down to a certain pair on the phone system, they will also need to go into configuration programming and set the feature.Config password and knowledge of wiring and programming required. Note you need to purchase a license to "re-broadcast" music on phone systems, paging equipment etc.Canada license - http://www.socan.ca/licensees/faq-licensingUSA license - http://www.ascap.com/licensing/Penalties:The Penalties Under U.S.C. TITLE 17, the law allows copyright owners to receive as damages for infringement between $500 and $100,000 for each work infringed

http://www.retrevo.com/support/Nortel-T7316E-Telephones-manual/id/2877ci958/t/2/ there is a manual and trouble shooting

Do you mean the feature light or the backlight for the display? The feature light can be set to on or off.

To set the light, press Save then 1 (for light on) or zero (light off). Press the desired memory key to associate with the feature and then enter the code from your telephone provider for that feature. Press Save and then label the memory key.

To use the feature light, press the memory key (as selected above) and then lift the handset. Press either Handsfree or Mute. The feature and the light will turn on or off. When the phone is not in use, then Feature On will be seen in the display.

The backlight is not adjustable. You can adjust the contrast with the Contrast button. Backlights do fail over time (but it's not a repair I recommend if the phone is out of warranty).

The manual is available here: http://www.aastratelecom.com/cps/rde/xchg/en-ca/hs.xsl/21564.htm . Look at the bottom of the center section for the PDF.

I hope this helps.

Cindy Wells

voicemail access by the network jo sim hai us pe agar ye subidha diya hai to

feature 981
enter password
listen for promt to change greeting.

for main greeting

press feature 983
if 3 digit extensions enter 1020000 if 2 digit extensions enter 120000

press AA
press grtg
press 1
press rec
press ok to end recording
press ok

press rls
To Listen to the Greeting, press Play. To ReRecord, press RETRY. Press OK to accept Greeting.

It could be that the background music feature is turned on but doesn't have a misic player attached. Try entering in feature #86 while the handset is in its cradle.

usually there is a small slide switch on the side of the answering machine that you can use to control how many rings before it answers. if that is a new digital model you will likely have to go into the menu to set it up. often your choices are two, four or toll saver.

robert

Please take a moment to rate this solution thanks

Programming should be done from the M7310, M7324 or the T7316E set. Administration access code: Feature * * 2 3 6 4 6 which also is Feature * * A D M I N.
If asked for a password enter the same 2 3 6 4 6.

If that doesn't work you may have the newer Compact ICS or the Modulur 0x32 control unit wish will be Feature * * 8 4 6 3 which is T I M E. Password is 2 2 7 4 2 which is B A S I C or A D M I N which is 2 3 6 4 6.
When in programming just press the next button(lower right arrow) until you see what you want to change. Then press show ( top right arrow) ,then change if you want to change it. If you pass it, just press back (lower left)
Example: To change the Time & Date Press next until you see Time & Date. Then show Then change Then change again, change it if you need to, Then next again until you see what you need to change. For example; only the hour needs to be changed for day light savings time. Just press next until you come to the Hour. Then Change it. Then press release RLs when your done.

Feature *80

You need to go into system programming and set that extension to "Forward no answer" to the extension of the voicemail.

If you dont know what that means, I would call someone in, as you can ruin your system by doing the wrong things.

Reset the system. Just kill power and let stand for 10 seconds before restoring power.

If problem persists, programming might not be set correctly for the types of lines you have.

To disable DND on a Norstar system,
dial FEATURE # 8 5
from the set.

The way 4 line phones work is that you need 4 lines on every jack that is connected to your phone.
You see the light probably because one of the phones has line conected and you see line appearance.

try to check the telephone wire connections. or try to use the other phone box to test.

tanderburg is fine but ask about dealer or agent near you for availlable technical support(this in case you have video conference in your businnes ).-ask for second hand machine to save your money and check it will befor you pay anything.-check for availlable manual on line-complete your connetion from radio shack near you.

google speakerphone 210 manual for choices.

Question edited for clarity. Question moved from Video Consoles category. Trying to find a manual. Are you sure that model is correct? Eircom should give you a manual PDF. https://www.google.com/search?q=Eircom+perform+100+manual and https://www.google.com/search?q=Eircom+perform+100 ..

Good question but no 'make model (what it is). Base units have an antenna, make sure it is extended. Make sure the batteries in the satellite hand sets are good as they send out the signal to the base unit to be 'in range'. Not sure about the PIN request, refer to the manual. They are all online. Google make model manual ..