Top 20 Jet Tech Systems 20 in. F16DP Built-in Dishwasher Questions & Answers

Try searching for commercial liquid detergent. Companies like Ecolab will sell it.

Ready light is there to tell you the thermostats have cycled off, rinse temp first and then wash temp after. if the wash temperature is low (below 160F) then we need to look at either the thermostat for wash or the heather is bad. if bot the temperatures are ok then it is just the light that is bad. If the rinse temperature shows 205F on analogue thermometer, a secondary reading is necessary with an external thermometer on the booster it self. These analogs thermometers are not so accurate.

for models equipped with a drain pump; verify that the pump is not clogged. if it hums during the fill cycle or rinse cycle then something is lodged inside. If it doesn't then it needs to be replaced. for models without the drain pump; something is interfering with the water flow. when the stand pipe is removed, the tank should empty in about one minute.

The detergent system on the Jet-Tech machine are all very similar. Near the solenoid valve under the machine, beside the drain connection, there are two wires, one red and one blue. Those wire will run the detergent pump when the machine calls for water. Two tube are attached to the pump. when looking at the pump from the front or clear plastic can be seen, the tube on the left (arrow going up) is connected to the container with the detergent. the tube on the right (arrow down) is connected to the back of the unit to inject the detergent into the tank. Some precaution should be taken to assure that the connections are tight and not leaking. if the tube shows signs of crystals inside, it should be replaced as the detergent as crystallized within. Search by part number or description

On the F-14, the booster thermostat must be satisfied. The rinse thermostat must work properly and or the rinse heater. follow the diagram. This kind of troubleshooting is done by qualified technician. Remember to unplug the unit before opening the panels. It could be just a burnt wire on the rinse booster heater connection. .

a plug can be warm. if it is hot to the touch, stop using it and have the machine checked and the receptacle check by a qualified technician.

Most Jet-Tech dishwashers has one adjustable rinse thermostat and one fixed wash thermostat. The wash thermostat can be substituted with an adjustable thermostat. Location depends on the model. F-18 are located on top. F-22 are located under next to the wash tank. Search by part number or description

If the machine will fill on its own when it is empty then the rinse cam on the timer is defective

No idea as i would either make my own or go to general store in alicante and ask the nice man if he has anything that would do the job if the original parts were not available

www.jet-tech.com/products/F-18DP/f18_tech_manual.pdf

Copy and paste that link into your internet address bar or type it in.
That is your manual

Hi,

That is not that hard to fix and you can easily buy the parts yourself online...

Here is a tip that will help you with the online buying...

How to Buy Appliance Parts Online

heatman101

If this is a common problem then ring the manufacturer, if not you will need to have it replaced.

Question edited for clarity. Question moved from Cars and Trucks category. This appears to be a Dutch Maker, we are in North America. There is some help here, but I don't see the wiring for that model, although there is a parts manual. The link may work better for where you live. https://www.google.com/search?q=elettrobar+e35h+wiring+diagram+pdf ..

These error messages both point to a sensor problem. Error 12.1 This error is related to the boiler temperature sensor. Consider the following: Look for a short circuit in the sensor. Inspect the cables and plugs for any issues. Ensure the sensor is correctly connected.If needed, replace the boiler temperature sensor. Error 22.2: This error pertains to the tank temperature sensor. Possible causes include: Short circuit in the sensor. Cable failure or plug failure. Sensor not properly connected. You may need to check the sensor wiring, connections, and replace the temperature sensor if necessary.

Fast enough for you! We don't 'SEND' anything to anyone.

PART ?: Generic Version

Midea https://www.midea.com > dam > dishwashers > O... PDF Please read this manual carefully before using the dishwasher and. Keep this manual for future reference. TORRINO. Page 2. SAFETY INFORMATION. 3. CONTENTS. 48 pages

USER MANUAL

Midea https://www.midea.com > built-in-dishwashers PDF When using your dishwasher, follow basic precautions, including the following: • Read all instructions before using the dishwasher. • Use the dishwasher ... 136 pages Missing: WP5a ‎' Show results with: WP5a

Midea Wp5C Service Manual - ManualsLib

ManualsLib https://www.manualslib.com > ... > Dishwasher > Wp5C View and Download Midea Wp5C service manual online. Wp5C dishwasher pdf manual download. Also for: Wp5d.

It depends upon the material you are trying to repair but Araldite or any good quality two part epoxy will suffice to fill the hole. Ensure the area is dry and clean then build up the repair . Larger holes will require multi additions of epoxy.

What type of media? https://www.google.com/search?q=Media+drawer+cannot+close 'make model (what it is)' in all questions please, first 3 words. ..

There is normally a D-shape that has to be in the right orientation on the spindle shaft. Some have a small recessed Allen screw or a way to adjust. They are all a tight fit. ..

Make and model of dishwasher may help yu get an answer

Put in olle dishwasher parts and where you live . This should come up with shops that do the spares