Rotel Rsx-1056 Receiver - Answered Questions & Fixed issues
ROTEL RCD-951 TM can not open tray.
Hello Ruben, so you do not open the CD holder tray of your Rotel, the problem is that the belt that transmits the rotation of the engine to the mechanism of the car, may be stretched and therefore the car does not open, this is the most common fault in this type of CD players
You should replace it, if you can not do it, look for a specialized technical service
I hope you can solve the problem
Greetings Franco Dosil
Hola Ruben, por lo que cuentas, no se abre la bandeja porta CD de tu Rotel, el problema es que la correa que trasmite el giro del motor al mecanismo del carro, puede estar estirada y por lo tanto el carro no se abre, esta es la falla mas habitual en este tipo de reproductores de CD
Deber?s reemplazarla, si no puedes hacerlo, busca un servicio t?cnico especializado
Espero puedas resolver el problema
Saludos Franco Dosil
https://elektrotanya.com/rotel_rcd-951-tm.pdf/download.html
http://bwgroupsupport.com/downloads/manuals/rotel/RCD-951-OM.pdf
10/9/2021 5:20:27 PM •
Rotel Audio...
•
Answered
on Oct 09, 2021
•
469 views
I have a rotel amp model no is ra-313
I'm guessing you don't know for sure that it even needs fuses. They don't go out like they used to, as everything is controlled by a microprocessor(computer within your unit). I would suggest, that you, with the power plug pulled out, use an ohm meter to be sure that each fuse is shorted. If you need further assistance, or would like to inquire about a repair, please visit my website at audioserviceclinic.com. Thank you.
11/19/2014 2:07:39 AM •
Rotel Audio...
•
Answered
on Nov 19, 2014
•
184 views
Rotel RHB-10 amp channel not working
YOU ARE NOT RIGHT IT SHOULD GIVE AT LAEST A LOW VOLUME SOUND WITH A LOT OF DISTORSION AND A CRACKING NOISE IF DOES I GUESS THAT YOU HAD THIS AMP IN A PLACE WITH A LOT OF HUMIDITY AND YOU HAVEN'T WORK IT FOR SOME TIME IF I AM RIGHT PUT YOUR AMP IN THE SUN AND WORK IT FOR 10 MIN WITH A 5 MIN BREAK LET ME KNOW THE RESULTS
9/3/2014 1:51:50 PM •
Rotel Audio...
•
Answered
on Sep 03, 2014
•
402 views
Fuse for rotel amp for RB-870BX
IF THE FUSE YOU ARE PLACING IS THE SAME TYPE AS THE ORIGINAL YOUR AMP HAS A PROBLEM WHAT YOU MUST DO IS TO SLIGHTY INCREASE FUSE BY 100 MAMPS PER TIME IF IT IS IN THE TRANSFORMER CIRCUIT YOU CAN INCRESE IT BY 2 AMP MAX IF IT IS IN THE MOSFETS CIRCUIT YOU CAN INCRESE IT BY A MAXIMUM OF 500MAMP LET ME KNOW THE RESULTS
6/14/2014 7:40:33 AM •
Rotel Audio...
•
Answered
on Jun 14, 2014
•
535 views
Sound from only one channel
Turn off the other channel and listen only to the bad channel playing some music. Turn it up! If you hear any music the pre-amp is working and the power amp is faulty. If you don't, then the pre-amp is faulty. Because it's a stereo amp you have the good channel to compare with the bad. So you can do voltage tests, or "buzz" tests. Buzz Tests or where you apply a insulated tool to the circuits, a buzz will be heard. If it buzzers in the good channel it should in the bad. Ignore the power supply and don't short any parts out!
9/19/2013 12:43:50 PM •
Rotel Audio...
•
Answered
on Sep 19, 2013
•
110 views
My rotel preamp wont turn on what is the power converter it has blown?
It's more likely to be a fuse that's gone. If so it could be caused by faulty device on the heat sink. The only device that converts power is a Transformer. You can test this by simply putting a Volt meter on it's terminals. They are not hard to fit, however they have to be replaced by the same thing or one approved by Rotel.
4/2/2013 3:58:19 PM •
Rotel Audio...
•
Answered
on Apr 02, 2013
•
190 views
Not playing in stereo
You have blowin a IC in it, Power amps are not suppose to be use for the purpose you were useing it for.You are dam lucky they didn,t go up in smoke.
10/22/2012 5:42:49 PM •
Rotel Audio...
•
Answered
on Oct 22, 2012
•
195 views
Rotel rsp 1098
Hello EricJust look at its connections. If the input connections have any loose connections at both ends, of the graound connection to both the devices are not proper, this kind of fault [intermittent sound and static noise] can occur. Reconnect all the connections and check the connection wires. OK.
1/21/2012 6:00:42 AM •
Rotel Audio...
•
Answered
on Jan 21, 2012
•
777 views
The cd tray will not
most likely your CD player doesn't support the formatting of the CD you are trying to use.
you didn't mention if this happens to ALL the CDs you try to play or only for specific ones.
if you don't use a copied CD do you still have an issue?
4/5/2011 8:01:43 AM •
Rotel Audio...
•
Answered
on Apr 05, 2011
•
94 views
Not finding what you are looking for?