Rotel RSP-1069 Silver 7.2 Surround Sound Processor - Answered Questions & Fixed issues


hi
it sound to me that when you biamp and driving speaker and woofer , you are over loading the fuses , suggestions
uprate the fuses till they stop blowing

Rotel Audio... | Answered on Dec 21, 2017 | 145 views


Probably the EEPROM, the heart and brain of the appliance.
I had the same issue with my AIWA, could not figure out the cause, took it in, tech told me EEPROM is blown.
Not economical to repair.

Rotel Audio... | Answered on Nov 20, 2017 | 97 views


Your changer has lost its mind and is doing crazy things.just like mine. Software issue not repairable.. Go shopping.

Rotel Audio... | Answered on Sep 13, 2017 | 101 views


Try interchanging the speakers. If the right channel works, you have a problem with your speaker.

Rotel Audio... | Answered on Nov 19, 2016 | 316 views


Check the rest of the power supply, for example the transformer if there is no power at all. If you are getting some indication of power, check the voltage regulator circuit.

Rotel Audio... | Answered on Apr 30, 2016 | 279 views


Hi Awal. Interesting problem. Have you tried another pair of leads? What source are you using please, cd tuner etc? I noticed the the names for the five audio/video inputs can be customized by the user, Maybe there is a firmware issue? With the unit being surround sound Have you tried running in 2 chanels only?

Rotel Audio... | Answered on Jan 16, 2015 | 114 views


I'm guessing you don't know for sure that it even needs fuses. They don't go out like they used to, as everything is controlled by a microprocessor(computer within your unit). I would suggest, that you, with the power plug pulled out, use an ohm meter to be sure that each fuse is shorted. If you need further assistance, or would like to inquire about a repair, please visit my website at audioserviceclinic.com. Thank you.

Rotel Audio... | Answered on Nov 19, 2014 | 106 views


YOU ARE NOT RIGHT IT SHOULD GIVE AT LAEST A LOW VOLUME SOUND WITH A LOT OF DISTORSION AND A CRACKING NOISE IF DOES I GUESS THAT YOU HAD THIS AMP IN A PLACE WITH A LOT OF HUMIDITY AND YOU HAVEN'T WORK IT FOR SOME TIME IF I AM RIGHT PUT YOUR AMP IN THE SUN AND WORK IT FOR 10 MIN WITH A 5 MIN BREAK LET ME KNOW THE RESULTS

Rotel Audio... | Answered on Sep 03, 2014 | 249 views


IF THE FUSE YOU ARE PLACING IS THE SAME TYPE AS THE ORIGINAL YOUR AMP HAS A PROBLEM WHAT YOU MUST DO IS TO SLIGHTY INCREASE FUSE BY 100 MAMPS PER TIME IF IT IS IN THE TRANSFORMER CIRCUIT YOU CAN INCRESE IT BY 2 AMP MAX IF IT IS IN THE MOSFETS CIRCUIT YOU CAN INCRESE IT BY A MAXIMUM OF 500MAMP LET ME KNOW THE RESULTS

Rotel Audio... | Answered on Jun 14, 2014 | 373 views


I do not know anything about your brand or market, but I have had good success with replacement remotes at http://www.replacementremotes.com/
They have a very wide selection of mostly refurbished remotes.
Originally supplied with RSX 1058 is this:
http://www.replacementremotes.com/ROTEL/Buy-RR-1061-RR1061-Audio-Remote-Control.html

Rotel Audio... | Answered on Jan 18, 2014 | 163 views


Turn off the other channel and listen only to the bad channel playing some music. Turn it up! If you hear any music the pre-amp is working and the power amp is faulty. If you don't, then the pre-amp is faulty.
Because it's a stereo amp you have the good channel to compare with the bad. So you can do voltage tests, or "buzz" tests. Buzz Tests or where you apply a insulated tool to the circuits, a buzz will be heard. If it buzzers in the good channel it should in the bad. Ignore the power supply and don't short any parts out!

Rotel Audio... | Answered on Sep 19, 2013 | 91 views


It's more likely to be a fuse that's gone. If so it could be caused by faulty device on the heat sink.
The only device that converts power is a Transformer. You can test this by simply putting a Volt meter on it's terminals. They are not hard to fit, however they have to be replaced by the same thing or one approved by Rotel.

Rotel Audio... | Answered on Apr 02, 2013 | 74 views


You have blowin a IC in it, Power amps are not suppose to be use for the purpose you were useing it for.You are dam lucky they didn,t go up in smoke.

Rotel Audio... | Answered on Oct 22, 2012 | 129 views


Hello Eric
Just look at its connections. If the input connections have any loose connections at both ends, of the graound connection to both the devices are not proper, this kind of fault [intermittent sound and static noise] can occur.
Reconnect all the connections and check the connection wires. OK.

Rotel Audio... | Answered on Jan 21, 2012 | 540 views


most likely your CD player doesn't support the formatting of the CD you are trying to use.

you didn't mention if this happens to ALL the CDs you try to play or only for specific ones.
if you don't use a copied CD do you still have an issue?

Rotel Audio... | Answered on Apr 05, 2011 | 80 views


I'd call or email Rotel service@rotel.com
Rotel of America
54 Concord St.
North Reading, MA 01864-2699
tel: 978 664 3820
fax: 978 664 4109

Rotel Audio... | Answered on Mar 30, 2011 | 330 views


If your powered subwoofer could accept speaker level input, like, say a Klipsch KSW-series, you wouldn't need it.

Rotel Audio... | Answered on Mar 14, 2011 | 273 views


Hello
It can be bought from most of the electronic spare part shops near to you. You must have the borken belt in hand as sample. it will help you to choose the correct replacement. OK.

Rotel Audio... | Answered on Mar 12, 2011 | 239 views


Before we throw in the towel, turn it off and exercise every control a lot of times throughout its range, particularly the Tape Selectors. Sometimes oxides will develop on seldom used controls and their 'normally closed' contacts will not pass a signal.

Rotel Audio... | Answered on Dec 26, 2010 | 349 views


The "no disc" message is a generic one indicating that the disc couldd not be read. This can be caused by a dirty lens (most common) or faulty optics. If you can gain access to the optics, try cleaning the lens using a cotton swab and alcohol. If that fails to resolve the problem, then the optics probably have failed and need to be replaced.

Dan

Rotel Audio... | Answered on Oct 08, 2010 | 103 views

Not finding what you are looking for?
Rotel RSP-1069 Silver 7.2 Surround Sound Processor Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Rotel Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5686 Answers

The Knight
The Knight

Level 3 Expert

76046 Answers

Mike Duncan
Mike Duncan

Level 2 Expert

219 Answers

Are you a Rotel Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...