20 Most Recent Belkin (F5D5231-4) Router - Page 5 Questions & Answers

PS3 And XBOX :: BELKIN



Step 1:Connect Modem - Router - Computer (Wired)

Step 2:Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3:On the Left click firewall

Step 4:Leave the Password blank and click submit

Step 5:Disable it and click apply changes

Step 6:Scan and connect in the Xbox/PS3/Wii

Step 7: Get the IP Address of the Xbox/PS3/Wii

Step 8:Open Router Setup in the Computer

Step 9:On the left under Firewall Click DMZ

Step 10:Enable the IP Address of the Xbox/PS3/Wii in it

Step 11:Click Apply Changes

Step 13:On the left Under Utilities click System settings

Step 14:Scroll down to the bottom

Step 15:Enable UPnP

Step 16:Click apply changes

Step 17:Test the connection ,Check the NAT

If working then let me know

======================================...
If it is still not working

Open Router setup

At the middle Under internet settings check the WAN IP

IF it starts with 192.168. or 172.16 Then you will have to contact your internet service and ask them to completely bridge the modem

When you installed the router, you provided a password/passphrase for connecting to your wireless network.
Apparently you didn't write this down or someone else set up the router.
If you don't have access to the admin console on the router either, you'll have to do a factory reset of the router to allow you to set it all up all over again.
This time, make a note of your passwords.

WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works

I would need your model number to answer that for you.

Thanks

Reset the router:

Step 1 Locate the reset pinhole on the back of the unit.

Step 2 With the unit powered on, press and hold the Reset button.

Step 3 Hold the Reset button for about 10 seconds.

Step 4 Release the Reset button.

Step 5 The unit will reboot. Allow 20-30 seconds before reconnecting.

Step 6 The device is now at factory defaults.

Note: Do not recycle power during the reset procedure.

When it says hold for about 10 seconds, don't hold for more than ten seconds or the procedure will likely fail, if ten seconds doesn't work try 5 seconds.

After you reset the router, restart your computer

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

just update your firmware
this is the link to update your firmware
http://www.belkin.com/uk/support/article/?lid=enu&pid=F5D8635uk4A&aid=14489&scid=0

Setting the router's administrator password

All Belkin Router's ship without an admin password. If you require an admin password then follow the below instructions.

Setup steps:

1. Connect the computer to one of the four LAN ports on the router.
2. Open a web browser on the computer.
3. In the address bar of the web browser, type http://192.168.2.1
4. Click Login in the upper right-hand corner of the page. The router does not ship with a password, so just click Submit.
   
5. Click on System Settings under Utilities on the left-hand side of the opened page.
   
   
6. You will see a feature called, "Administrator Password". Type in your current password (default leave blank).
   .
   

7. Click "Apply Changes". Your new password is now active.
   

Note: Do not forget the new password and keep it somewhere safe. If you forget your password, you'll be unable to access your router's settings. If you forget or lose your password, you'll need to "restore to factory default". This will reset the password to its default, as well as erase any and all other settings you may have changed.

hi there, the best solution for you is to reset the password. Hold the reset button for at least 5 seconds.
Then access the HTTP portal and use these:

Username: N/A Password: (blank)
Hope this helps,
levibit

Wireless light will only Lit ON, only if any one of the wireless device is connected to the Router
First connected the router and computer through Ethernet Cable
Open Web browser and type 192.168.2.1 Toward left side you can find Channel and SSID(Click on it) By defualt no password so leave the box blank and click on submit
You can find an option called Wireless channel Try the channel 3,6,7,9 and 11
Also if its asking for the N/W key then you can find from the Belkin Router Setup Page itself
Toward left side you can find Security under Wireless( Click on that option)
there you can find security mode and you can edit the password or change the password from the same screen
Hope this will help you

Its seems to be a configuration issue
Open Web broswer and type >192.168.2.1 You will get Belkin Router Setup page Towards the left side Under Utilities you can find RESTORE FACTORY DEFAULTS( CLICK ON IT) it will ask for a password, By default no password so leave the Box blank and click submit Click OK for all the disclaimers
Once you get the Belkin Router Setup page back
Toward left side you can find CONNECTION TYPE( Click on it) Select DYNAMIC and click NEXT For Hostname you can leave it Blank Then click on Apply changes
Once you get the Belkin Router Setup page back
Toward left side you can find MAC ADDRESS( Click on it)
Then click on CLONE and Click APPLY CHANGES
Hope that will fix the issue
Or else you can always call belkin support, they will assist with the steps

WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works

PS3 And XBOX :: BELKIN



Step 1:Connect Modem - Router - Computer (Wired)

Step 2:Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3:On the Left click firewall

Step 4:Leave the Password blank and click submit

Step 5:Disable it and click apply changes

Step 6:Scan and connect in the Xbox/PS3/Wii

Step 7: Get the IP Address of the Xbox/PS3/Wii

Step 8:Open Router Setup in the Computer

Step 9:On the left under Firewall Click DMZ

Step 10:Enable the IP Address of the Xbox/PS3/Wii in it

Step 11:Click Apply Changes

Step 13:On the left Under Utilities click System settings

Step 14:Scroll down to the bottom

Step 15:Enable UPnP

Step 16:Click apply changes

Step 17:Test the connection ,Check the NAT

If working then let me know

======================================...
If it is still not working

Open Router setup

At the middle Under internet settings check the WAN IP

IF it starts with 192.168. or 172.16 Then you will have to contact your internet service and ask them to bridge the modem

its really complicated . You need to flash Router Memory
Rate my answer and Support me

Perform a hardware reset on the router

Setup steps:

1. Locate the reset hole on the router. The button will be on the back or side of the router.
   See images below:

1. Leave the router powered on.
2. Use a paperclip (or similar) to press and hold in the reset button for 10 seconds.
3. Remove the paperclip.
4. Wait approximately one minute for the router to restart.

The settings for the router have now been reset back to their default.

If you need more help come back.Post / thumbs / testimonial are welcome!

it will definitely work and compatible for your system
rate the solution

1. Powercycle your equipment (unplug the power to your router and your modem)
2. Wait 15 seconds then plug equipment back in.
3.If your Modem runs off signal from a tower try and get more signal simply by moving modem closer to a window.
4.Check your connections to the modem and to the router, ensure the wires are plugged all the way in.
5.Using your wireless signal from your computer pc or laptop ensure you have sufficient signal you may have to move closer to the router, once in a while you will be to far from your router to have a good connection.
6. Make sure the ventilation slots on modem and router are not blocked.
7.Check to see how far your modem is away from any electrical equipment your modem should be away at least 3 feet away.
8. If you are able to keep connection directly plugged into your modem from your computer most likely there is an issue with the router, In this case you can always reset your router there may be a configuration error in your router, To reset simply press and hold reset button on the back of the router for approximately 15 seconds or until router restarts, Caution by resetting your router will reset back to factory default and your router will be unsecure once again.
9. When your are disconnected from the internet make sure that the Connection itself isnt still connected if your connection itself is connected and you are unable to get online you may need to renew your ip address. usually your ip address automatically renew's once the router and modem have been powercycled (unplugged and plugged back in) however you may need to manually renew your ip.
10.Windows Xp: Start/Run/CMD and press ok
A.Type ipconfig /release
B.Type ipconfig /renew
Windows Vista/7 Start/All Programs/Accessories/Right click on command prompt and hit run as administrator.
A.Type ipconfig /release
B.Type ipconfig /renew then restart your computer
If you are a Mac user:Here is a link to show you how to renew http://support.apple.com/kb/TS1920 If your continue to get disconnected contact your ISP (Internet Service Provider) Check and ensure that it is not an issue on there end

Step 1 Go to Start> Control Panel > and select Network connections.

Step 2 Right click on your network card (for 2000 and XP only)and select Properties.

Step 3 Select the Configure button.

Step 4 Under the Advanced tab you will see two boxes; Property and Value.

Note: Depending on the type of Ethernet card you are using the headings in the Property box will be slightly different.

Step 5 Select each heading in the Properties box until the Value box displays the speed of your Ethernet card (it will look like this: Auto-Negotiation, 10Mb Full, 100 MB Half, etc..). You want to select 10mb Full Duplex.

Step 6 Keep clicking OK until you get to the desktop. Your computer may ask you to reboot depending on the version of Windows you are running.

Are you looking for the wireless password or the password of the router?
If you want the password of the router, then try the default password of the router. If the default password doesn't work then you will need to reset the router and reconfigure the router.
If you are looking for the wireless network password, then you will need to open the set up page of the router. Is there any computer connected to the router ? If not then you will need to connect the computer to the router. Or any other computer which is able to go online using the router. Check the IP address on that computer. open the set up page of the router. Set up page of the router is the page where you will find all the settings of the router. under the wireless section you will find the wireless network password
Click here for more information about the routers and wireless network.

First light only will get green if connection is ready.

• If your connection is DSL with user name and password you need to setup your connection type PPOE
• If your connection is Cable just you ned to clone your mac Address to be connect to internet

after this the light of your router will turn on.

Remember power cycle modem and router to be connected.

Any question ask me again and tell me the name of your ISP Internet provider.

please rate me Techbelkin.

Need your OS please.