20 Most Recent Evenflo Evaporative Cool Mist Humidifier - Page 4 Questions & Answers

make & model

the Number should start with 43-52XX normally it should be on the back plate.

This sound is could mean that the life of the gear has been used up.

This is a common problem. It is easily fixed for $10 + Shipping. The gear needs to be replaced. Try this link to have someone call you. [email protected]
Remove the gear and turn on the unit to see if the noise still exists.

• If noise stops, the gear and coupling needs to be replaced

How old is is and how often do you use it?

Every get it working? Here's a link where the same problem was solved. https://www.doityourself.com/forum/humidifiers-dehumidifiers/590652-wait-5000-troubleshooting-no-water-flow.html

This a repair forum, you need to deal with manufacture. If you look on the instructions that came with unit, the warranty info is there and the place to return it.

Is the little ultrasonic disk clean, or is there hard scale on it? If there are hardened deposits on the disk they will stop it from vibrating. Be careful not to damage it by scraping or digging with a tool. I have found that the best way to clean it is with a Waterpik, turned all the way up. It often takes ten minutes of work to clear it off. This is MESSY, do it in the shower, or outside.

Call a vendor to ask for assistance. https://www.carelparts.com/ 800-825-2148

After replacing the Water Panel, turn the control knob to the “Test/Reset” position until the “Change Water Panel” light blinks to reset the Water Panel change indicator timer.

English please.

You need to check to make sure the condenser fan is blowing and that the condenser coil is clean. You absorb heat inside the refrigerator, compress that heat with the compressor, then expel the heat at the condenser (the part of the system that blows hot air). If you can't expel that heat, the unit will lock itself out until you reset it

You may find your manual at one of these two sites. ManualsLib Makes it easy to find manuals online Free User Manuals and Owners Guides ManualsOnline com

I DON;T KNOW. MOST WATER IS LET IN WHEN NEEDED BY FLOAT VALVE AT BOTTOM OF BOTTLE OR LOWER. PERHAPS IT NEEDS CLEANING. CONSIDER USING STRAIGHT VINEGAR IN LEAKING SIDE THEN GOOD SIDE. IF NOT OK, YOU MAY HAVE TO TAKE UNIT APART TO INSPECT FOR CAUSE.

https://tadanoamerica.com/dealers If anyone using Fixya is searching, this is a link to dealer phone numbers in the United States to request.

Hello, sounds like rhe solenoid valve is stuck open. This will keep water flowing through the humidifier even if the Furnace is off. The solenoid valve will have to be replaced.

Perhaps your machine stops when it has reached the desired humidity level you selected. It doesn't have to be empty when it reaches that selected level. My mother thought the same thing but was so relieved to find out it was working properly all the time.

I see no question here.

I have had times where my Crane humidifier won't produce mist if I haven't turned it on for several days (4+) or more. The water that sits in the reservoir may develop a film on the ultrasonic element which inhibits the creation of the mist to come out the top of your humidifier. I would lift off the tank and empty the reservoir. Then VERY GENTLY with a piece of paper towel, wipe the ultrasonic element (looks like a disk the size of a quarter at the bottom of the reservoir) to clean off any film. Then replace the tank and let the reservoir fill up the tank and try it again. If your humidifier runs properly for a minute and then makes a whirring noise and goes silent (like the motor stopping), then it's a motor problem. The humidifier motor may have gone out of alignment due to bumping or rough handling of the humidifier when cleaning or emptying it. If that is the case, you will have to empty the humidifier reservoir, unscrew the base, and find the screws holding down the motor and check for misalignment. Loosen them a little and put it back together and try again. Best of luck thebqe