20 Most Recent Ricoh Aficio 1027 All-In-One Laser Printer Questions & Answers

1. Separation bias error. A separation bias leak signal is detected. Causes. • High voltage supply board defective

That is fuser code and needs to be reset in the service mode, it will not go away by turning the off and back on.

Good afternoon from Chicago, shiva262,

I'm not sure from your post above, but it appears that you are looking for a driver for your Ricoh Aficio 1027 All-In-One Laser Printer. If that is in fact the case, try the following steps to resolve your problem:

1. If your Ricoh Aficio 1027 All-In-One Laser Printer is connected to a Windows-based PC, use Windows Update to try and locate, dwnload and install the correct driver software.

2. Navigate to the following links and follow the instructions:
http://www.ricoh-usa.com/downloads/local/manuals/multifunction_bw/aficio1027.pdf

http://www.ricoh-usa.com/downloads/popup/popup_manuals_drivers_download.aspx?path=http://support.ricoh.com/bb/html/dr_ut_e/rc2/model/x1022_27/x1022_27en.htm

I hope these are helpful in solving your problem. Good luck!

Regards,

Enolram

The 1027 uses a TWAIN driver for scanning, and you can get a TWAIN driver here:

http://www.opendrivers.com/driver/283630/ricoh-aficio-mp-2500-network-twain-driver-4.25.01-windows-2000-xp-2003-2008-vista-free-download.html

1. Download driver from http://support.ricoh.com/bb/pub_e/dr_ut_e/0001153/0001153018/V3100/r29694en.exe2.If that doesn't fix the issue immediately try http://support.ricoh.com/bb/pub_e/dr_ut_e/0001154/0001154861/V861/r30275en.exe

en.. try PDF Editor Software Pro,Best PDF Editor Software for Mac,adds OCR technology, covers all the PDF editing power and the 6-in-1 PDF conversion functions on the basis of the standard version, PDF Editor Software, to provie you a smarter way in dealing with PDF documents. PDF Editor Software,Outstanding OCR accuracy and format preservation, OCR enables you to search, correct, and copy the text in a scanned or image PDF directly,Support 17 OCR recognition languages:: English, Turkish, Greek, German, French.... http://www.pdf-editor-software.com/

Check the connection to the machine. Otherwise the IP changed on the machine or the network you're on IP changed.

to reset it just enter service mode and cycle power. But first take out the fuser ( right side of copier 2 screws ) and check that the 2 rollers hot and pressure are touching each other no gap between them. The unit you have is a nice unit, for service to fix if replacement is required would be about 300.00 or so... -Carl

there is two ways to achieve this, either enter servisse mode using yellow 1 0 7 and stop (hold stop for a few seconds) go to copy sp the go to 5 mode and the scroll to 801 memory all clear... this will reset the machine completely... if you not feeling so brave inside 801 there is sub menus just stroll down to clear UCS

www.ricoh-usa.com/support/support.aspx

you must clean developer and drum section. after that you must put new developer and initialize it. After that place in correct toner.

check f the printer and scanner kit r installed!

sc546 is a fuser ready temp problem. it requires a reset procedure: enter SP mode.touch Copy SP..touch SP DIRECT then press 7807# on the keypad then execute...turn power off and then back on

sounds like you have the wrong print driver for the mfp

SC 650 - communication timeout error between SBCU and duplex unit.Verify the duplex mechanical and electrical components(gears,actuators,sensors).

cannot set up the scan to folder because that machine cannot put a hard disk that used for scan to folder just only can use the network twain

I haven't seen such problem in this printer Anyhow uninstall the printer software and reinstall it You might have PCL6 driver Try RPCS Driver from Ricoh Web