Top 20 Nordic Track Incline Trainer X9i Interactive Questions & Answers

If you wish to get more details; check the site linked here. http://electro-medical.blogspot.com/

Take it of your Android system and just use the factory settings.

I have same issue. Turn off the wifi and then turn the unit off, wait 1 min and turn on. They can't seem to fix!

Computer panel is possibly dead. I had them send me a completely new panel for my x9i. I was under warranty, though. It's actually pretty easy to install yourself, with their instructions and another person.

Have you tried turning the power off, unplugging the system . Wait 15 minutes then plug it in and power up.

Have you connected the tablet to the internet via WiFi? As I am reading on your treadmill it has the ability to connect to internet and that maybe what it is looking for, so it can update itsself.

you need to replace the key pad I’m happy to assist further over the phone at https://www.6ya.com/expert/james_1cb31da1bc8c6102

tighten the belt with machine running .The side it runs to is the side u will tighten about 45 deg clockwise.

Turn the bolts at the end of the treadmill anti clockwise.

Check this link out, there's some useful information that could solve your problem if you're still dealing with this loop. best of luck! https://thatguyreviews.com/treadmill-display-rebooting-ifit/

You should immediately replace the console. That console will just keep getting worse. This is endemic of this brand, however it usually happens a lot further in the life of the unit. When you call Nordictrack have your model number.

I also have an X9i treadmill hardly used .smells like its burning. It also is not acting right while on it. Whats causing this? it cost $2000.00 no joke I thought Norditrak was a better company. I purchased it from Back country.

Sounds like a software issue. Call nordictrack at 888-308-9616

reset follow the next step When the treadmill is not in use, press the "Stop," "ENTER" and "QUICK START" buttons in rapid succession. The "RESET" button can also be used, in place of the "Stop" button.God bless you

Wow, lots of scary posts. If I had read this before, I would never have bought it. :) Anyways, there is a solution. I dont think this post was ever resolved, so I ran across this site that offered a few steps that allowed me to fix the reboot issue and a few nice folks who would reply to any questions. This sounds like a common problem with ifit on treadmills. I came across this site a few weeks back and it helped! There's a few folks there that could offer suggestions too. best of luck! https://thatguyreviews.com/treadmill-display-rebooting-ifit/ Hope this helps!

try to RUN the software calibration, see your instr. manual how to enter and proceed for easy diagnose, troubleshooting, and fix it.God bless you

Disconnect wifi and boot machine. This works well for a non-internet workout. I had a similar problem--endless looping of the boot up routine--which ultimately fixed itself when I tried updating. I believe they came out with a new update which must have fixed some bug in the system.

Step 1:

RUN the calibration software . and fix it. God bless youhe Steps for Newer Style Console Calibration1.Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)2.Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).3.Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.4.If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.5.Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.6.Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.7.Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.8.Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.9.Press ENTER. CL26 should display in the TIME window. You should then see the letter "E." 10.Press ENTER. You should see "SS" or "55" in the console. 11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.12.Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own. 13.When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position. 14.Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.15.If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Step 2:

Dear Sir:Adjust the reed switch, see the diagram attached, clean, and tight the connector very well.Anyway I recommend to call the service Help, in the place where you did buy your treadmill.However you can RUn THE SOFTWARE calibratin for diagnose, troubleshootin, and fix it, follow the steps in your instructions manual.sincerely. God bless you

https://www.livestrong.com/article/410922-the-controls-are-not-working-on-a-nordictrack-treadmill/