Precor 9.35 Premium Series Treadmill - Answered Questions & Fixed issues

Procedure 2.3 - Accessing the User Parameter Program This procedure allows you to change the following settings: • Set Measurement Units • Enable/Disable Password • Set User Name Procedure 1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker. 2. Press keys STOP,5,6,7,1 sequentially. 3. The display will momentarily read SELECT UNITS 4. The currently selected measurement unit will then be displayed. 5. Use the UP, DOWN arrow keys to toggle between U.S. STANDARD and METRIC. 6. Press the ENTER key to select the currently displayed measurement unit. 7. The display will momentarily read, PASSWORD 8. Use the UP, DOWN arrow keys to select either PASSWORD ENABLED or PASSWORD DISABLED 9. Press the STOP or ENTER key to exit the program.

Precor Error 05, Key Depressed at Power Up Probable Cause 1. A key is permanently depressed on the display. 2. An interface chip (IC) has failed in the upper PCA's keypad. 3. Liquid (cleaning solution or sweat) may be on the surface of a touch sensitive display. Corrective Action

1. Disconnect the keypad cable from the upper PCA. Reset power to the machine. If the Error 05 is eliminated, the keypad is the cause and should be replaced.
2. Disconnect the keypad cable from the upper PCA. Reset power to the machine. If the Error 05 still appears, the upper PCA* is the cause and should be replaced. *Upper PCA's most commonly do not come with software. Remove the software (chip) from the existing upper PCA prior to replacement and install into the new upper PCA.
3. Wipe away all liquid from the touch sensitive display. Reset power to the unit. If the Error 05 is eliminated, the liquid was the cause.

This link will take you to the parts available for these models. Because most machines are serial number specific, you will need to narrow your search based on your particular model and serial number. Precor Repair Parts for 9 35 9 35i Treadmills Consumer SPORTSMITH net

Turn off you machine always, also disconnect the treadmill remove the cover and clean the motor fan and the motor with air cans.

this is the answer: Probable Cause This error message almost always indicate an upper PCA problem when they are consistently displayed. Failures causing this error message to be displayed are rare. Corrective Action If the error message is consistently displayed when the unit is powered up, the upper PCA should be replaced. It is possible to see this message displayed intermittently due to external causes. If the units A.C. input significantly dips during the power up test sequence the test could fail resulting in this message being displayed. Treadmills operating on non-dedicated A.C. circuits may see this message displayed on an intermittent basis. God bless you

please see the details and proceed according. God bless you

• Error 05, Key Depressed at Power Up

Check RPM Feedback: The most common cause for the timer to stop after 7 seconds on a Precor elliptical is NO RPM feedback. Start by checking the connection of the speed sensor to the lower board. If necessary, reset the connection. Also, inspect the magnet located on the user's right crank arm (versions 1 and 2) or the user's left crank arm (version 3). The magnet passes the speed sensor with each revolution of the crank arm. Ensure that the magnet is installed correctly, with its south pole facing the speed sensor. You can verify the magnet polarity using another magnet or a compass. Speed Sensor Spacing: Confirm that the spacing between the speed sensor and the magnet is within the range of 1/8" to 1/4". Adjust if necessary. Battery and Power: If your elliptical has a battery, check its status. A low battery could cause issues. Consider using the optional power adapter kit to ensure consistent power supply. Error Codes and Clearing Logs: Check for any error codes displayed on the console. Clear the error codes and power down the unit. Inspect cable connections to ensure they are fully seated. Power on the unit and monitor the error code log for any reoccurrence. Professional Assistance: If the issue persists, consider reaching out to professional repair services or contacting Precor support for further assistance.

Il existe deux raisons pour lesquelles votre v?lo elliptique Precor EFX 556 d?marre lentement. Tout d'abord, un probl?me ?lectrique, tel qu'un cordon d'alimentation mal branch? ou endommag?, ou m?me une prise d?fectueuse, pourrait survivre. Un condensateur d?fectueux ? l'int?rieur de l'appareil, qui peut causer des retards au moment de la mise sous tension, est une autre explication. Pour r?soudre ces probl?mes, commencez par v?rifier les connexions ?lectriques. Envisagez d'appeler un technicien qualifi? pour diagnostiquer et r?soudre un probl?me ?lectrique ou ?lectronique si le probl?me persiste.

hello there, check if the lift control system is detected the lift is moving in the opposite direction of the issued lift command. This error would happen when the lift was already in motion (typically downward) when a lift command in the opposite direction (lift upward) was issued.

A slow boot up on a Precor EFX 546 elliptical machine can be caused by several factors, including:

1. Low battery voltage: If the battery voltage is low, the machine may take longer to boot up. This can be due to a weak or old battery, or a problem with the battery charger.
2. Dirty or corroded contacts: Dirt, dust, or corrosion on the battery contacts or other electrical contacts can interfere with the machine's ability to start up quickly.
3. Faulty console or display board: If the console or display board is malfunctioning, it may take longer for the machine to boot up or may not boot up at all.
4. Loose or damaged cables or connections: Loose or damaged cables or connections can prevent the machine from starting up properly and may cause a slow boot up.
5. Outdated software: If the software on the machine is outdated, it may take longer for the machine to boot up or it may not start up at all.

To troubleshoot a slow boot up on a Precor EFX 546, you can try the following steps:

1. Check the battery voltage and replace the battery if necessary.
2. Clean the contacts on the battery and other electrical components.
3. Inspect the cables and connections for damage or looseness.
4. Check for any error codes or messages on the console or display board and consult the user manual for troubleshooting steps.
5. Check for any available software updates and install them if necessary.

If none of these steps resolve the issue, you may need to contact a professional technician for further assistance.

Hey Fabian, it's possible that the resistance motor or sensors on your wife's Precor 556i/AXGE may need to be recalibrated. Try powering off the machine, unplugging it for a minute, and then plugging it back in to see if that resets the calibration. If the problem persists, you can try recalibrating the machine manually. There should be instructions in the user manual or online. If that doesn't work, then contacting customer service or a certified technician may be necessary. I hope this helps!

If you have checked the safety switch on your Precor 9.45 treadmill and everything seems to be intact, and the "reset safety switch" message still won't go away, it's possible that the switch itself is faulty or the console is not receiving the signal from the switch. You can try cleaning the switch and the area around it, and also check the wires that connect the switch to the console to make sure they are not damaged. If the switch or wires appear to be damaged, they may need to be replaced. If cleaning and checking the switch and wires doesn't resolve the issue, it's recommended that you contact the manufacturer or a qualified repair technician to further diagnose and fix the problem. They may be able to provide additional troubleshooting steps or suggest other possible solutions.

Everything is fixable :>) Service manual in the link https://www.google.com/search?q=Precor+546i+Elliptical+Cross-Trainer+stuck+at+highest+position ..

This is an error code for 1 of 2 things. Something was spilt on the display causing a detected malfunction. Or, you are experiencing a power sag where the unit is plugged in. Try an isolated AC circuit. (Nothing else is ON or plugged in)

Two likely candidates: Belt or tread. Lubricating the tread would be the easiest starting point; but if you're running at 7 or more you've probably already thought of that. If the cover isn't too difficult to remove, you can expose the drive belt and the squeaking volume change would be an indicator that the drive belt is the problem.

Contact Precor direct. Details at the bottom of the page. It uses a non-standard method of resistance. https://www.precor.com/en-ca/efx%C2%AE-546i-elliptical-fitness-crosstrainer%E2%84%A2 ..

http://www.precor.com/products/media/english/Treadmill_932i_Manual_Maintenance_Reference_Assembly_English.pdf

Service Manual, 9.31, 9.33, 9.35.fm (sportsmith.net) PRECOR 9.33 OWNER'S MANUAL Pdf Download ' ManualsLib Precor LOW-IMPACT TREADMILLS 9.33 User Manual ' 86 pages ' Also for: LOW-IMPACT TREADMILLS 9.31 (manualsdir.com)

You will need to replace the battery

A sticky button is the most likely cause https://www.google.com/search?q=Model+956i+won%27t+speed+up ..