Precor 932i Treadmill - Answered Questions & Fixed issues

HI There, Did you get this worked out? Possibly the IFT drive?

Precor Error 05, Key Depressed at Power Up Probable Cause 1. A key is permanently depressed on the display. 2. An interface chip (IC) has failed in the upper PCA's keypad. 3. Liquid (cleaning solution or sweat) may be on the surface of a touch sensitive display. Corrective Action

1. Disconnect the keypad cable from the upper PCA. Reset power to the machine. If the Error 05 is eliminated, the keypad is the cause and should be replaced.
2. Disconnect the keypad cable from the upper PCA. Reset power to the machine. If the Error 05 still appears, the upper PCA* is the cause and should be replaced. *Upper PCA's most commonly do not come with software. Remove the software (chip) from the existing upper PCA prior to replacement and install into the new upper PCA.
3. Wipe away all liquid from the touch sensitive display. Reset power to the unit. If the Error 05 is eliminated, the liquid was the cause.

Precor Error Code 05

Precor Error 05, Key Depressed at Power Up Probable Cause 1. A key is permanently depressed on the display. 2. An interface chip (IC) has failed in the upper PCA's keypad. 3. Liquid (cleaning solution or sweat) may be on the surface of a touch sensitive display. Corrective Action

1. Disconnect the keypad cable from the upper PCA. Reset power to the machine. If the Error 05 is eliminated, the keypad is the cause and should be replaced.
2. Disconnect the keypad cable from the upper PCA. Reset power to the machine. If the Error 05 still appears, the upper PCA* is the cause and should be replaced. *Upper PCA's most commonly do not come with software. Remove the software (chip) from the existing upper PCA prior to replacement and install into the new upper PCA.
3. Wipe away all liquid from the touch sensitive display. Reset power to the unit. If the Error 05 is eliminated, the liquid was the cause.

Precor Error Code 05

Several things you can try here. If the stops switch is stuck it will cause the display to be blank. There also may be a loose connection to the upper or lower board. You can remove the front cover and check the connections to the lower board. The upper display connection will look like a cat 5 cable. Unplug it and plug it back in. That same cable runs up and plugs into the upper board. Check that connection as well. If those don't work then it may be the lower PCA.

Typically on the Precor Treadmills if there are errors on the unit, you can press and hold the stop button for 3-5 seconds and it will go into the error log. Not sure what model you have.E-2 is not what normally shows up on the screen. Do you mean Error 2 was displayed? From what I have read on Error 2's it could be a upper PCA issue, or possibly a dip in AC input during the power up sequence.Treadmills require a dedicated line, meaning it is on its own dedicated circuit on your fuse panel/circuit breaker.What exactly is the treadmill doing? Is it constantly showing Error 2 on the screen? Call up Precor tech support. They will be able to give you advice, and or get you connected with an authorized Precor factory trained technician who will be able to get you back up and running.

When start-up prompt "PRESS ENTER TO BEGIN OR PRESS QUICKSTART" appears, access the Club Program by sequentially pressingSTOP, SPEED , SPEED , SPEED , RESET, SPEED , SPEED , andSPEED . (Numbers on the display appear in sequence: 4, 5, 6, 5, 1, 5, 6,and 5.)Note: You must sequentially press each key within 4 seconds of each otheror the display reverts back to the start-up prompt.6. Maximum Speed: Use any or key to designate a speed limit between1 and 15 mph (1 and 24 kph). The speed you designate limits the speed ofthe treadmill. Press ENTER when the desired speed appears.7. Maximum Workout Time: Use any or key to designate a time limitbetween 10 and 240 minutes. The amount of time you choose limits thelength of a person's workout. (This does not include the automatic 5-minutecool-down period.) Press ENTER to accept the time limit.Note: Continuous pressure on the arrow key lets you scroll through thenumbers being displayed.8. Language: Use any or key if you want to change the language. You canchoose between English, German, Spanish, or French. When you changethe language, you affect all the prompts and informational messages thatappear on the display. Select the language being displayed by pressingENTER.9. Custom Courses (C964i only): The course profile appears in the centerdisplay. (If you want to customize course number 2, press ENTER.)When you enter custom mode, you have the ability to "draw over" an existingGod bless you

Dear Sir:I am recommend you to exchange the board. If you do not have ENOUGH experience will be better to buy a new one, or call some tech profesional for to execute this delicate work. The causes can be various, Maybe you have SHORT circuit in the motors, power supply, see the block diagram.God bless you

Il existe deux raisons pour lesquelles votre v?lo elliptique Precor EFX 556 d?marre lentement. Tout d'abord, un probl?me ?lectrique, tel qu'un cordon d'alimentation mal branch? ou endommag?, ou m?me une prise d?fectueuse, pourrait survivre. Un condensateur d?fectueux ? l'int?rieur de l'appareil, qui peut causer des retards au moment de la mise sous tension, est une autre explication. Pour r?soudre ces probl?mes, commencez par v?rifier les connexions ?lectriques. Envisagez d'appeler un technicien qualifi? pour diagnostiquer et r?soudre un probl?me ?lectrique ou ?lectronique si le probl?me persiste.

hello there, check if the lift control system is detected the lift is moving in the opposite direction of the issued lift command. This error would happen when the lift was already in motion (typically downward) when a lift command in the opposite direction (lift upward) was issued.

A slow boot up on a Precor EFX 546 elliptical machine can be caused by several factors, including:

1. Low battery voltage: If the battery voltage is low, the machine may take longer to boot up. This can be due to a weak or old battery, or a problem with the battery charger.
2. Dirty or corroded contacts: Dirt, dust, or corrosion on the battery contacts or other electrical contacts can interfere with the machine's ability to start up quickly.
3. Faulty console or display board: If the console or display board is malfunctioning, it may take longer for the machine to boot up or may not boot up at all.
4. Loose or damaged cables or connections: Loose or damaged cables or connections can prevent the machine from starting up properly and may cause a slow boot up.
5. Outdated software: If the software on the machine is outdated, it may take longer for the machine to boot up or it may not start up at all.

To troubleshoot a slow boot up on a Precor EFX 546, you can try the following steps:

1. Check the battery voltage and replace the battery if necessary.
2. Clean the contacts on the battery and other electrical components.
3. Inspect the cables and connections for damage or looseness.
4. Check for any error codes or messages on the console or display board and consult the user manual for troubleshooting steps.
5. Check for any available software updates and install them if necessary.

If none of these steps resolve the issue, you may need to contact a professional technician for further assistance.

Hey Fabian, it's possible that the resistance motor or sensors on your wife's Precor 556i/AXGE may need to be recalibrated. Try powering off the machine, unplugging it for a minute, and then plugging it back in to see if that resets the calibration. If the problem persists, you can try recalibrating the machine manually. There should be instructions in the user manual or online. If that doesn't work, then contacting customer service or a certified technician may be necessary. I hope this helps!

If you have checked the safety switch on your Precor 9.45 treadmill and everything seems to be intact, and the "reset safety switch" message still won't go away, it's possible that the switch itself is faulty or the console is not receiving the signal from the switch. You can try cleaning the switch and the area around it, and also check the wires that connect the switch to the console to make sure they are not damaged. If the switch or wires appear to be damaged, they may need to be replaced. If cleaning and checking the switch and wires doesn't resolve the issue, it's recommended that you contact the manufacturer or a qualified repair technician to further diagnose and fix the problem. They may be able to provide additional troubleshooting steps or suggest other possible solutions.

Everything is fixable :>) Service manual in the link https://www.google.com/search?q=Precor+546i+Elliptical+Cross-Trainer+stuck+at+highest+position ..

This is an error code for 1 of 2 things. Something was spilt on the display causing a detected malfunction. Or, you are experiencing a power sag where the unit is plugged in. Try an isolated AC circuit. (Nothing else is ON or plugged in)

Two likely candidates: Belt or tread. Lubricating the tread would be the easiest starting point; but if you're running at 7 or more you've probably already thought of that. If the cover isn't too difficult to remove, you can expose the drive belt and the squeaking volume change would be an indicator that the drive belt is the problem.

Contact Precor direct. Details at the bottom of the page. It uses a non-standard method of resistance. https://www.precor.com/en-ca/efx%C2%AE-546i-elliptical-fitness-crosstrainer%E2%84%A2 ..

http://www.precor.com/products/media/english/Treadmill_932i_Manual_Maintenance_Reference_Assembly_English.pdf

Service Manual, 9.31, 9.33, 9.35.fm (sportsmith.net) PRECOR 9.33 OWNER'S MANUAL Pdf Download ' ManualsLib Precor LOW-IMPACT TREADMILLS 9.33 User Manual ' 86 pages ' Also for: LOW-IMPACT TREADMILLS 9.31 (manualsdir.com)

You will need to replace the battery