20 Most Recent
Precor Efx 5.21i - Page 5 Questions & Answers
No power on my precor c964i control board
Starting at the outlet, follow power into the machine. If you are getting power past the circuit breaker and in to the power board, chances are your lower board is toast. The only solution is to replace the item with a new or known good used board. The following links will take you to a video on how to use a multimeter to verify power.
Video about Multimeter Testing
I keep getting a speed error message when I start the belt
Replacement Parts for Fitness Exercise Equipment at SPORTSMITH
Precor Error LS, Speed Sensor Signal Missing
Probable Cause
1. Intermittent or open connection of the speed sensor (reed switch) wiring.
2. Reed switch is defective or has intermittent connection.
3. Drive motor brushes are bad.
4. Lower PCA is bad.
Corrective Action
- Inspect the speed sensor (reed switch) wiring for damage or poor connection to the lower PCA. Replace damaged wiring or reset connection as necessary.
- Using an ohm meter, test the reed switch while rotating the drive pulley. The reed switch will close when the magnet passes in front of it.
- Inspect the drive motor brushes and replace if necessary.
- Test unit with a known good lower PCA. Replace lower PCA if necessary.
Precor Error Code LS
Belt has moved to the left
Adjusting Tension on a Treadmill Running Belt
It is necessary to properly tension a
treadmill beltwhen it is replaced. After time, a belt can stretch and may begin to slip. When this happens, it is necessary to adjust the tension of the running belt to stop it from slipping. Manufacturers of treadmills generally agree on one of three procedures for
how to tension a treadmill running belt.
- Adjust for no slippage of thetreadmill walking belton the front roller (Often referred to as the "Stomp Test")
- This procedure works well for a previously installed belt that is now slipping.
- Underside of belt should be free of any glazing/wax buildup.
- Rollers must also be free of wax buildup.
- Be sure belt tracking/centering is correct before proceeding.
- The most popular speed for this adjustment is 2mph to 3mph.
- Try to slow the belt by applying pressure with your foot against the belt movement while grasping the handrails. If the running belt slow, slips or stops (and the front roller does not) adjust BOTH adjustment bolts 1/4 turn clockwise. Test again and repeat adjustment if necessary.
- This procedure requires twobelt gauges or calipers
- This procedure works well when installing a new belt.
- This procedure requires you to stretch the belt. Depending on the manufacturer*, this varies between .4 and .6 percent. A dial on the gauge or caliper will indicate the amount of stretch. *Consult the owner/service manual for proper tension.
- If you are working on a previously tensioned belt you will need to release the tension before attaching the gauges or calipers.
- Gauges or Calipers unavailable
- Release the tension on the belt.
- Using a yard stick or tape measure, place two marks on the left and right edges of the belt and deck 36 inches apart (or 50 inches if you prefer).
- Adjust the left and right tensioning bolts until both sides measure 36 3/16 inches (or 50 1/4). This is equal to .5% of stretch.
- Test for proper tracking and tension, adjust if necessary.
How to Tension Treadmill Walking Belt that Slips
Panel will not light up.new battery did not help
On C846 version 1 units, set the on/off switch in the "on" position. It will be necessary to start pedaling for the bicycle to "power up".
For any other units, we recommend checking for any loose, crimped, or visually bad wires.
Make sure the speed sensor on your bike is working.
You can run a quick test by using a magnet to swipe in front of the sensor to see if it is sending signal to your console.
For any further troubleshooting please do no hesitate to call our Tech Support Team 888-713-2880
Or check us out online
https://www.sportsmith.net/
Percor treadmil error codes
Precor Error 05, Key Depressed at Power Up
Probable Cause
1. A key is permanently depressed on the display.
2. An interface chip (IC) has failed in the upper PCA's keypad.
3. Liquid (cleaning solution or sweat) may be on the surface of a touch sensitive display.
Corrective Action
- Disconnect the keypad cable from the upper PCA. Reset power to the machine. If the Error 05 is eliminated, the keypad is the cause and should be replaced.
- Disconnect the keypad cable from the upper PCA. Reset power to the machine. If the Error 05 still appears, the upper PCA* is the cause and should be replaced. *Upper PCA's most commonly do not come with software. Remove the software (chip) from the existing upper PCA prior to replacement and install into the new upper PCA.
- Wipe away all liquid from the touch sensitive display. Reset power to the unit. If the Error 05 is eliminated, the liquid was the cause.
Codigo de error
List of Error Codes for Precor Fitness Equipment
- Precor has standardized their error code messages across all their equipment so that each error will have the same meaning regardless of what model or equipment type the message appears
- Here we list each error so that you can click through the specific error for additional details about the cause and action to correct the error
- E2, Lift Error
- E4, Incomplete Initialization
- ERR, EEPROM Problem
- Error 00, Memory, RAM, EEPROM Test Error
- Error 01, Memory, RAM, EEPROM Test Error
- Error 02, Memory, RAM, EEPROM Test Error
- Error 03, Memory, RAM, EEPROM Test Error
- Error 04, Memory, RAM, EEPROM Test Error
- Error 05, Key Depressed at Power Up
- Error 09, Lower PCA Memory Test Error
- Error 10, Line Frequency out of Acceptable Range
- Error 11, Watchdog (Upper PCA)
- Error 12, Watchdog (Lower PCA)
- Error 13, Fan at Incorrect Speed
- Error 14, Fan Fail
- Error 15, AC Input Voltage Too High
- Error 16, AC Input Voltage Too Low
- Error 20, Too Many Maximum Power Request in 1 Second
- Error 21, Too Many Maximum Consecutive Power Requests
- Error 22, No Motor Pulses at Start Up
- Error 23, Motor Pulses Missing after Start Up
- Error 24, Reduce Speed Requested, Speed is not Reducing
- Error 25, Motor Pulse Count over Acceptable Limit
- Error 26, Motor Pulse Width Incorrect
- Error 27, Too Much Drive Motor Current
- Error 28, Temperature Too High
- Error 29, Excessive AC Input Current
- Error 30, 31, 32 and 33, Communications Error
- Error 37, E-Stop Not Working
- Error 40, No Lift Motion Detected
- Error 41, Lift has not Responded in Acceptable Time
- Error 42, Lift Position Value Out of Range
- Error 43, Zero Switch not Found
- Error 44, Un-commanded Lift Motion
- Error 45, Lift Moving in Wrong Direction
- Error 46, Low Battery Voltage (AMT12 Only)
- Error 50, Too Much Brake (Magnet) Current
- Error 53, Can't Read Target, Can't Find Home Switch
- Error 54, Target Pulses Lost During Operation
- Error 55, Brake Home Switch Activated Unexpectedly
- Error 60 or "Temporarily Out of Order", Auto Stop Not Working (TRM Treadmills)
- Error 61 or "Temporarily Out of Order, Auto Stop Not Present" (TRM Treadmills)
- Error 62, Vertical Sensor Failure (AMT12 Only)
- Error LS, Speed Sensor Signal Missing
- Error 70, LPCA Not Read
- Error 71, Blank LPCA
- Error 72, AMT LPCA Version Unknown
- Error 73, AMT LPCA Record Bad
- Error 74, Refurbished Head
- Error 75, Refurbished Head
- Error 76, AMT Head Stride Count Less than the LPCA
- Error 77, AMT UPCA Stride Count Greater than the LPCA
- Error 78, AMT Belt Replacement Warning
- Error 79, AMT Belt Replacement Required
Error Code List for Precor Fitness Equipment
Not finding what you are looking for?