Precor 546 Elliptical - Page 9 - Answered Questions & Fixed issues
Promaster pro plus 2 error code 31
Error 31 on your Promaster Pro Plus 2 treadmill could indicate a variety of issues, such as a problem with the motor or the motor controller. Here are a few troubleshooting steps you can try:
- Power cycle the treadmill: Turn off the treadmill and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again. Sometimes, simply resetting the treadmill can resolve error codes like Error 31.
- Check the motor connections: Make sure all the wires and connections to the treadmill motor are secure and properly connected. Loose connections could cause error codes to appear.
- Inspect the motor controller: The motor controller regulates the speed and operation of the treadmill motor. Check for any visible signs of damage or overheating on the motor controller. If you notice any issues, you may need to replace the motor controller.
- Contact customer support: If you're unable to resolve the issue on your own, it's best to contact the manufacturer's customer support for assistance. They can provide specific troubleshooting steps for your treadmill model and may be able to offer a solution or arrange for repairs if necessary.
By following these steps, you can hopefully resolve Error 31 on your Promaster Pro Plus 2 treadmill and get it working again.
2/20/2024 3:17:53 PM •
Exercise &...
•
Answered
on Feb 20, 2024
•
29 views
Treadclimber TC 200 treadles rubbing in the middle
Check Alignment:
First, ensure that the treadles are properly aligned. Misalignment can cause rubbing. Make sure the treadles are parallel to each other and evenly spaced.
Tighten any loose bolts or nuts that secure the treadles to the frame.
Inspect the Walking Belt:
Examine the walking belt for any signs of wear, fraying, or damage. A damaged belt can cause uneven movement and rubbing.
If the belt is worn out, consider replacing it.
Lubricate the Bolts and Joints:
Apply lubricant (such as silicone spray) to the bolts and joints where the treadles connect to the frame. This can reduce friction and prevent rubbing.
Be cautious not to over-lubricate, as excess lubricant can attract dust and debris.
Check for Obstructions:
Look for any foreign objects (dirt, debris, or small items) that might be caught between the treadles or near the alignment bolts.
Remove any obstructions to ensure smooth movement.
Inspect the Alignment Bolts:
Make sure the alignment bolts are properly adjusted. They should be tightened enough to prevent excessive movement but not too tight to cause rubbing.
Adjust the bolts if necessary.'
Test the TreadClimber:
After performing the above steps, test the TreadClimber to see if the rubbing issue persists.
If the problem continues, consider contacting the manufacturer or a professional technician for further assistance.
2/15/2024 10:31:07 PM •
Exercise &...
•
Answered
on Feb 15, 2024
•
116 views
How to fix E03 for a Superfit treadmill
I think I had something similar happen. It may be that your motor drive is overheated. If you smell burning from the motor stop immediately. You might just need to make sure this is properly lubricated.
1/26/2024 8:15:23 PM •
Exercise &...
•
Answered
on Jan 26, 2024
•
74 views
Got an error code of 5103 07. AFG 3.1AT
Hi,
if this is a treadmill, please power cycle the treadmill to start. If the errors are not in the product documentation, please attempt to confirm them by calling the manufacturer first. it might be an issue like too much friction under the belt that can be cleared up by leaving the platform and applying oil to the section under the belt. or you could possibly need to schedule a repair. But making the call will help point us in the right direction.
Thank you.
1/20/2024 4:32:05 PM •
Exercise &...
•
Answered
on Jan 20, 2024
•
250 views
I have a Pro Form 995i treadmill that I just bought recently and when I hit the iFit button it says “Not connected please check users manual”. Is there any way I can reset it?
Question edited for clarity.
iFit is a subscription service, you have not connected to WiFi, haven't subscribed, haven't paid, so you don't get the service. You can't 'reset it'.
IFIT DISCLAIMER:
iFit requires an internet connection and Wi-Fi to function. You will be required to provide your credit card information upon sign-up for iFit. Your Commitment Period may be month-to-month or twelve (12), eighteen (18), or thirty-six (36) months, depending on your agreement. Terms shall apply to your iFit use and subscription during your Commitment Period and any subsequent Renewal Term.
Unless you cancel your account or notify us at least twenty four (24) hours prior to the expiration of your commitment period that you do not wish to renew your subscription, your iFit subscription will automatically renew for an additional month, one (1) year, or two (2) year period, as applicable, for the same duration as your initial commitment period ("The Renewal Term"), and you authorize us to bill the then-applicable membership fee and any taxes to the payment method we have on record for you.
It is all here
https://www.proform.com/blog/faq-power-995i-treadmill/
..
1/13/2024 8:28:42 PM •
Exercise &...
•
Answered
on Jan 13, 2024
•
31 views
Not finding what you are looking for?