Landice L8 80 LTD Executive Trainer Treadmill - Answered Questions & Fixed issues

that is a loss of speed error. you only get rid of it when the belt starts moving again I’m happy to help further over the phone at https://www.6ya.com/expert/howard_079189dd4959a511

BOB MARLIN SAYS NO

You need to get someone out to look at it. Noise issues are rarely able to be diagnosed remotely.

Hello, it is either the control board or the overlay. I would think it is probably the start button on the overlay that is stuck. The solution is to replace the overlay.

There could be a few different things causing your Landice L7 treadmill to race to top speed when turned on. Here are some potential causes and solutions:

1. Motor Control Board: The motor control board may be malfunctioning and sending the treadmill into top speed automatically. If this is the case, you will need to replace the motor control board.
2. Console Board: The console board may be sending incorrect signals to the motor control board, causing the treadmill to race to top speed. If this is the case, you will need to replace the console board.
3. Speed Sensor: The speed sensor may be malfunctioning and sending incorrect signals to the motor control board. If this is the case, you will need to replace the speed sensor.
4. Calibration: The treadmill may be out of calibration, causing it to race to top speed. To recalibrate the treadmill, consult your owner's manual for instructions.

It's recommended to consult with a qualified technician to diagnose and fix the issue to avoid causing further damage or injury.

It sounds like you normal routine has made the motor hot and then when you slow down the residual heat is causing the motor to cut out. Check the vents in the motor for fluff or blockage. https://www.google.com/search?q=Landice+L7+treadmill+stopping+at+cool+down ..

Troubleshooting and link to Landice Support in the link. https://www.google.com/search?q=Landice+L9+Treadmill+display+not+working ..

You need to open it and cheek the belt and the bearing ,cheek for wear and tear if past inspection try lubricant ,all the best.

What even is this question?

Communication Error between upper and lower board generally produced by a physical disconnection between harness and the the apparatus. Reseat the harness.

the speed sensor is in the front drive wheel. it is a sensor located on the left-hand side you will see a wire going to the sensor. then a magnet is on the wheel and when it passes by you get your speed. I’m happy to help further over the phone at https://www.6ya.com/expert/howard_079189dd4959a511

is this a home model and did you buy originally? the reason I ask is that Landice home L8 models have a lifetime parts warranty. contact Landice and they will be able to assist you over the phone for free. you either need a new keyboard panel(bad buttons), or a new lower computer board. both easy fixes on a Landice I’m happy to help further over the phone at https://www.6ya.com/expert/howard_079189dd4959a511

If you wish to get some details; visit the site linked here. Pull up older posts..... http://electro-medical.blogspot.com/

Check the motor for its stability . If you wish to get some details about treadmill repair ; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Unit may be in kilometers. Switch to miles.

follow this steps and fix it. God bless you SAFETY SHUTDOWN Loss of Speed Signal" or "L5" WITH belt movement This is usually an indication of a speed control malfunction. The upper board is not recognizing a signal pickup from the speed sensor. This could be due to the speed sensor being misaligned, improper connection, or bad speed sensor. Refer to the flowchart on page "SAFETY SHUTDOWN Loss of Speed Signal" or "L5" WITH NO belt movement The speed sensor is not recognizing any motor movement. This displays the error message to the upper board. NOTE: USE THIS FOR DIAGNOSING THE PWM/RELAY COMBO BOARD

How long does it run for when it starts...you need to give a detailed description for better diagnosis

if you give me the email, i can send you. my email [email protected] bless you

1) rUN THE SOFTWARE CALIBRATION for diagnose and troubleshootin.2) Lube the deck belt 3) Lube the rollers bearing4) Measure the input voltage motor, if there are the motor need repair5) Measure the output voltage boad, for input voltage motor, if there are not the board is faulty. see the block diagramGod bless you.