20 Most Recent Theater Research TR-9500 Car Subwoofer Box Car Speaker - Page 9 Questions & Answers

The message "Wrong SRC/TM" on a BEOSOUND 9000MkIII when pressing '72' while in test mode (Shift 90258) and set to 'CD' could indicate that there is an issue with the source selection or the test mode itself. To resolve this issue, you can try the following steps:

1. Check the source selection: Make sure that the correct source (CD) is selected on the BEO4 and that it is functioning properly.
2. Check the test mode: Verify that the test mode has been activated correctly and that the Shift 90258 code has been entered correctly.
3. Check for firmware updates: Make sure that the firmware on the BEOSOUND 9000MkIII is up-to-date. If there is a firmware update available, install it to resolve any issues with the test mode.
4. Factory reset: If the above steps do not resolve the issue, a factory reset of the BEOSOUND 9000MkIII may be necessary. This will restore the unit to its original settings and resolve any software-related issues.

If these steps do not resolve the issue, you may need to seek further assistance from the manufacturer or a professional repair service. It's important to follow the manufacturer's instructions and safety guidelines when attempting to repair or troubleshoot your system to avoid damaging the unit or causing potential harm.

I apologize, but wiring diagrams for specific home appliances are not readily available to the general public. These diagrams are usually confidential and used by authorized repair technicians only. If you need to repair or replace the cord on your Lasko silent room heater Model 5628, I would recommend reaching out to the manufacturer or an authorized repair service for assistance. They should be able to provide you with the information and support you need to safely and effectively repair or replace the cord.

I'm sorry to hear that you're having issues with your Y performance teknique ICBM-9707B. To help diagnose the problem, please provide the following information:

1. What is the device supposed to do?
2. What is the exact error message or behavior you are encountering?
3. Have you tried troubleshooting steps, such as checking the power source or connecting cables?
4. Is there any recent hardware or software changes made to the device or the environment it is used in?

Providing this information will help me better understand the issue and provide more specific advice to resolve it.

I had the same problem with my Pioneer AVH-P4000DVD. Just got my 16GB sandisk micro cuzer in the mail from Radio Shack. Here is what I did to solve it:

1. Copied all the files that came with the Sandisk device to another location (in case I need them again)
2. Copied all the music I had put on the Sandisk since I got it to another location
3. Using a Windows PC, I right clicked on the drive in Windows Explorer and selected "format"
4. I re-formatted the cruzer mini to FAT 32, default size (yes, I know it was FAT 32 already)
5. Copied the music back to the cruzer mini
6. Plugged it into my radio and it works GREAT! instant access to any track

Before you do this: Reformatting the drive also gets rid of the software that makes the cruzer mini copy files super fast. It will take a lot longer to copy music to the drive. For me this is no big deal as the only reason I bought the drive was to put a bunch of music on it and then leave it in my truck.

Try cleaning the contacts with a q tip and rubbing alcohol and see if that helps.

The USB device error for an AVH-P3200DVD can be caused by a variety of issues, including a problem with the USB device itself, a problem with the USB port on the AVH-P3200DVD, or a problem with the software or firmware on the device. To troubleshoot the issue, you may want to try the following steps:

1. Check that the USB device is properly formatted and that it contains no corrupt files.
2. Try connecting a different USB device to the AVH-P3200DVD to see if the problem is with the USB port or the device itself.
3. Try using a different USB cable to connect the device to the AVH-P3200DVD to see if the cable is the problem.
4. Check for any software or firmware updates for the AVH-P3200DVD and apply them if necessary.
5. If none of these steps work, try resetting the AVH-P3200DVD to its factory settings.

If the problem persists, it may be best to contact the manufacturer for further assistance.

I NEED RADIO CODE FOR SIEMENS VDO 330886636. No.13 138 246. GM020521690276.PLEASE HELP ME.THANKS!

A possible issue could be a faulty power supply. In order to confirm, you can try plugging the power supply into separate power source to ensure that it is capable of supplying power to the unit. Additionally, the speaker connections may have become disconnected, so it would be beneficial to check the wiring in order to ensure that all connections are properly secured.

Vous devez ouvrir le couvercle du chargeur de CD et appuyer sur le bouton "Eject". Le chargeur de CD lib?rera alors les CD.

If it displays LOCKED 3 then leave it SWITCHED ON UNDISTURBED for as long as it takes to automatically reset itself.

Make sure you have the correct code

However if it says LOCKED 13 then your radio is fully locked (due to 13 or more wrong codes being entered previously ) and can only be reset by the Main Dealer or a Radio Decoding Service

There could be a few possible causes for the CD player in your Valencia MP36 not playing CDs properly. Here are a few things you could try:

1. Clean the CD. Dust, dirt, and fingerprints can all interfere with the CD player's ability to read the disc. Use a soft, lint-free cloth to gently clean the CD.
2. Check the CD for scratches or damage. If the CD is scratched or otherwise damaged, it may not play properly.
3. Check the CD player's laser lens. The laser lens is responsible for reading the CD and can become dirty or misaligned over time. If the laser lens is dirty, use a CD lens cleaner to clean it. If the laser lens is misaligned, you may need to have the CD player serviced.
4. Check the CD player's connections. Make sure that all of the connections between the CD player and the amplifier or receiver are secure.

If these steps do not help, it is possible that there is a problem with the CD player itself. In this case, you may need to have the CD player repaired or replaced.

I just fixed my 2005 RX330 CD changer jam, and saved $800-1000. It was easy, if you first spend $6 at:
http://www.carstereohelp.com
Here you will find pics and instructions on how to remove the stereo/changer. Mine was a Pioneer, and the stereo came out in 5 minutes. I could not find instructions how to take it apart, so I experimented a little. The secret was to take the top lid off the changer - 9 little screws, and a piece of black tape. Under the lid, I found my problem - a CD had been inserted too soon (the WAIT sign actually means what it says!), and I just lifted it off the top plate. Under the plate I could see 2 more CDs, in the 6 slot holder, but they seemed to be free and not jammed. So without reassembling the stereo, I plugged it back in. The changer cycled, I hit eject twice to get the other CDs out, and all is well.

'make model (what it is)' in all questions please.Googlemake model change radio languageyou can also use a smart phone with the Google Translate app on it and translate what you are seeing on screen.Also note that some units are for the Japanese domestic market and only come in Japanese.

This could be caused by a few different things. To troubleshoot, first check the fuse box to make sure the fuses for the radio and speakers are not blown. If the fuses are secure, then you should check the wiring connections to make sure they are connected properly and not loose or frayed. If the wiring connections are good, then the problem could be with the head unit itself and you may need to contact a professional for further assistance.

To reset your KD-R426, locate the reset button on the unit. This is usually located behind the faceplate. Once you've found the reset button, press and hold it for about five seconds. After a few seconds, you should see the message "RESET" appear on the display of your stereo. At this point, you can release the reset button.Your KD-R426 should now be reset and working properly. If you have any questions, or if you need help resetting your stereo, please consult your owner's manual or contact a qualified technician

It sounds like you are having trouble with the volume on your radio. This could be caused by a few different things. To troubleshoot, first ensure that the volume knob on the radio is turned up to its max. If the volume is already turned up, then you should check the speaker wires to make sure they are connected properly and not loose or frayed. If the wires are secure, then you should check the volume control on your amplifier to make sure it is not set to a low volume level. If the amplifier volume is already set to a high level, then the problem may be with the radio itself and you may need to contact a professional for extra help.

It sounds like your NHDT-W55 is having issues with displaying audio and video correctly. This could be caused by a faulty connection between the head unit and the speakers or a faulty wiring connection. To troubleshoot, first check all the connections between the head unit and the speakers to make sure they are securely connected. If the connections are secure, then check the wiring connections to make sure they are not loose or frayed. If the wiring connections are good, then the problem could be with the head unit itself and you may need to contact a professional for further help.

It sounds like you are having trouble with the radio and DAB reception when the head unit is in the cage/holder. This could be caused by either a faulty antenna connection or a faulty ground connection. To troubleshoot, first check the antenna connection to make sure it is securely connected. If the connection is secure, then check the ground connection to make sure it is properly connected to the chassis of your vehicle. If the ground is not connected properly, it can cause signal interference and reception issues. If these steps do not resolve the issue, then you may need to contact a professional for futher help.

If your 891 mini component system is not turning on, there could be a few possible causes for the issue. Here are some steps you can take to troubleshoot the problem:

1. Check the power source: Make sure the system is plugged in and that the outlet it is plugged into is functioning properly.
2. Check the fuse: If the system is plugged in and the outlet is functioning properly, the issue may be with the fuse. Check the fuse to see if it has blown and replace it if necessary.
3. Check the power cord: If the power source and fuse are both functioning properly, the issue may be with the power cord. Check the cord to see if it is properly connected and in good condition. If the cord is damaged, you may need to replace it.
4. Check the power switch: If the power source, fuse, and power cord are all functioning properly, the issue may be with the power switch. Check the switch to see if it is functioning properly and test it to see if it is turning the system on and off as expected. If the switch is not functioning properly, you may need to replace it.