20 Most Recent D-Link DI-604 4-Port Cable/DSL Router (DI-604) Broadband (di-604 (dont quote)) Bridge - Page 2 Questions & Answers

The following reset procedure will completely restore the default settings on your D-Link device including your password. This procedure applies to the DI-514, DI-524, DI-604, DI-614+, DI-624, DI-754, DI-764, DI-774, DI-784, DI-804V, DWL-700AP, DWL-800AP+, DWL-900AP+, DWL-1000AP+, DWL-2000AP, DWL-2100AP, DWL-6000AP, DWL-7000AP, and DWL-7100AP.

Step 1 Locate the reset pinhole on the back of the unit.

Step 2 With the unit powered on, press and hold the Reset button.

Step 3 Hold the Reset button for about 10 seconds.

Step 4 Release the Reset button.

Step 5 The unit will reboot. Allow 20-30 seconds before reconnecting.

Step 6 The device is now at factory defaults.

Note: Do not recycle power during the reset procedure.

The default user name for most D-Link devices is admin and the password is left blank.

Hope this helps! Give me thumbs please!

What you can do here is to try resetting the router , to do that press and hold the small reset button on the router for 15 seconds while power is ON and then after that power off the router for 10 seconds and then if you still have the setup CD you can just run it and check if that will detect the router. But after doing the reset and reconfiguration on it and still not working router is already bad and may need replacement.

Hi,

Try suggestions for you is to do the following:

1) First start with power cycle the router, unplug it and leave it unplugged for about 30 seconds then plug it back in and wait for all the lights to come on then see if the problem persists.

2) If the above suggestion doesn't work then try to reset your router to factory settings by taking an object with a small point and holding in the reset button on the back of the router for "atleast" 30 seconds then release the button wait for all the lights to come on and then see if the problem persists, if it still does then I would recommend purchasing a new router as the Repair cost would be High relevant to the cost of the new one.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

It looks like there are a lot of DNS servers that do not work correctly with the PS3. Below I will list a few DNS servers that do seem to work and you will need to manually configure the DNS settings for your PS3 to any of these addresses.

208.67.222.222
208.67.220.220
129.250.35.250
129.250.35.251
4.2.2.1
4.2.2.5

Make sure DHCP is enable in router and your network adapter ip address configure as ip get automatic.IF still not work then try to set ip address manually in the rane of another computer.
Uninstall network adpater driver then reinstall.
Then restart computer and router.
Then check .
Also type in cmd "ipconfig /release" then type in cmd "ipconfig /renew"
Then you can get ip.
Let me know if you need further assistance.
Thanks for using FixYa.

if u blow up ur house, it will fix it
seriously i did that to get rid of all the pikachus that were taking over my house
dude
SERIOUSLY
WTF MAN
DO WAT I SAID

On the computers that are not getting Internet access, check the LAN cables to the router. Does the Link LEDs on the router for these computers are ON?
If the LED lights are off then the LAN cable and/or network cards are faulty.
Check Device Manager on these computers to see if the LAN card is working and enabled. If not re-install the LAN drivers. If the driver installation cannot detect the LAN card then most likely the LAN card is faulty and needs replacing.
Get back to me with the results of these tests and I can advise what to do next.

I didn't think the D-link router actually had a clean light. ;)
my coffee pot flashes its light to let me know it needs cleaning. I just unplug it for a few seconds and the cleaning reminder goes away.

are any lights going off or flashing on mdm ? then call isp . . when was the last time you pwr cyc mdm AND router if it has been awhile try that turn both off for for 3 to 5 min turn mdm on first wait for dsl light wait 2 min turn router on wait 2 min try again if still have problems connect direct to mdm and if still doing it it isn't the router it is the internet connection or mdm

to get the settings for the route and find the address do the following

right click on the network computers in the system tray (bottom right hand corner)

then open the network center
then click on local area connection then go details

the address of your router is next to the IPv4 Defualt Gateway *.*.*.*

now type this into your browser and you should be at you settings page




easier way is to check the bottom of the modem itself and there should be a ip address just enter that into your browser

http://www.antifart.com/2006/09/02/d-link-di-604-firmware-rev-e.html

Before using these files, make sure you have the E Revision of that router, you can check by looking on the sticker that contains all the model information like serial, model number.

Be careful while doing a firmware upgrade, very easy to brick your router. Bricking refers to making the router no more useful than an expensive paper weight.

might be the router. try plugging the cord that goes to the input of the router directly into your computer and see if still same problem.

A simple solution would be disabling the firewall on the router and use your windows firewall. Your router might be blocking msn messager. Another solution which is harder under application on a router. Most routers have you can set that program to aloud on the Internet.

Go to RUN and type CMD and you will find a black window known as the command prompt. Herein type in ipconfig and you will get some IP addresses. The one under the Default gateway is the required IP address for the router.

Have you tried resetting the router? Reset the router and see if that helps.
Thank you,
Lee

your cable tv problem is not related to your computer issue.
Start your pc and enter the bios (usually by pressing F2 or Del) and navigate to the boot options. put the bootup options in a similar order to this, Floppy, CDROM, Primary harddisk. then disable network boot or add network boot to the end of the list.

they stay in the list for a set amount of time... that is based on the "lease time" that has been configured for ip addresses.

Hello,

Have you tried to reset your router? If not, do so. It will reset everything to factory default.

To reset, look for a hole near the ports, where it says RESET. Use a pointed object such as a paper clip.

Hope it helps.

next time it happens leave laptop on and plugged into router and unplug router only. If laptop now works problem is in the router you will probably have to reset router to default and use the router wizard to re-program!

Reset your router
Press reset button for 10 seconds it is in back side of router.
then access it with following link

http://192.168.1.1
or
http://192.168.0.1