20 Most Recent D-Link DP 301P (DP-301P) Print Server - Page 2 Questions & Answers

i have the cd that would allow you to factory reset the device once installed reply to this i will sent you the executable ..

Yes. In most cases you can reset your D-link DP-300 series or DP-301 series print server yourself even if you don't know the password or IP. This comes in handy in situations such as when the server has made up its own password after being connected to a new router.

Cross your fingers and try the following steps...

1) Install the psadmin software if you have not already. If you have lost the psadmin software then search for it on the web.
2) Start the psadmin software and click "factory reset".
3) If the software demands a password, try "SYSxxxx", where xxxx stands for the last four digits of the MAC address located on the underside of your server. (Example: if your MAC address were "63 XE 29 44 F2 96", then your password would be SYSF296.)
4) Click yes to confirm the reset.
5) Follow the non-intuitive instructions provided with your server to set it up again. (Note that a Quick Install Guide will likely be more useful than a manual for this step. If you have lost your Quick Install Guide then try downloading it from D-link's website, http:/www.dlink.com/default.aspx Locate your model via "product quick find" or "find your product" then click on "support resources" and look for a quick installation guide.)

Good luck!
Shahzad IT Department Mitsubishi Motors KSA

Unfortunately, I don't know of a way to manually reset this without using the web-interface.

However, if it was somehow reset already, the default password for this unit is nothing. They do not use a password by default, so try it without one.

Good luck!

Ryan

Check your power supply. If the transformer box is cold and the outlet has power, you'll need to replace it. You will need DC 5V, 2.5A and the correct adapter. Thus check with Dlink if your print server is still under warranty.

I hope this helps.

Cindy Wells

You need to connect to it (using the broswer at the PC of same LAN with the current ip of the print server). Then click on Tools TAB, click on "Reset" at left. You should see "Do you want to restore this device to factory default setting?". Click on "Apply"

It supports all below protocol so you can give print from IBM iseries .

TCP/IP Protocols Supported :

• BOOTP
• SNMP
• Telnet
• TFTP
• FTP
• LPD
• RARP
• DHCP

its all in the your site at gmail... you can ask to to see your password by clicking "forgot password" then answer all the question to made... you all the answer

usually by resetting it. pushing the reset button on the back it (tiny hole on the back) for 30 seconds, while plugged in to power,

Unfortunately, D-Link doesn't provide a way to reset the password if you lose it. This is from their website:

Forgot Password Unfortunately the D-Link Print Servers are secure and cannot be reset without the password. The unit will have to be sent to D-Link to be reset. Please contact our RMA department at 800-326-1688 M-F 7AM - 6pm Pacific time to return unit (US only). Nick

By default the DP 301P+ does not come with a password. If there is one installed (and you don't know what it is), you can reset the device to factory defaults from the Tools menu in the web configuration utility. Be aware that you will lose all settings in the print server when you do this.

Cheers
Nick

You may use the PSAdmin software to configure your print server even if you don't know the IP address. The only requirement is that the DP-300U has to be in the same network (subnet) as your PC running PSAdmin. In the PSAdmin, you will then be able to view or change the IP address.

Here is the link to download PSAdmin:
http://support.dlink.com/products/view.asp?productid=DP%2D300U#apps

Remember that if you also have forgotten the Admin password, you will have to ship the unit to D-Link in order to have it factory reset.

do you have the options set correctly on the remote computers assistant to use local devices

There should be a pinhole that allows you to do it with a paper clip...

You can find the details of the operator and the state they belong to .the operators wont reveal the address and name of any mobile numbers only higher officials can only get those information.
In order to trace the operator name and state you can try this link
http://www.indiatrace.com/trace-mobile-number-location/trace-mobile-number.php

I hope this will help you if it does do rate the answer
Thank you
regards
lalith

I am sure it is now toast and you cannot downgrade if the wrong firmware has been installed. I would ask D-Link.

https://www.youtube.com/watch?v=zKeXtyUMKjA Check out this video it might help you with your issue.

Please open router page and go to advanced just like in this emulator. http://support.dlink.com/emulators/wbr2310/adv_network.htm