20 Most Recent D-Link AirPlus Xtreme G DWL-2000AP 802.11g/b Wireless Access Point - Page 4 Questions & Answers

Hi.
Here is product home page. On "Support Resources" choose your right revision an than download what you want.

Hello,
It seems to me that the default IP address for the web interface is 192.168.1.1 or 192.168.0.1 .
Hope it helps.

connect the router with PC and you can find the manual for TV to find the network of the TV once you connected with the PC you need to change the ip address way to your TV network because your TV AND internet in different network once you change this router to the TV network with the help of IP address it will work

Do a hard reset of your router by pressing the reset button located at the rear of the router for 5 sec while the power on, the router will be reset st the factory default. Hope this will solve the problem

try 192.168.0.1
Usually that will be thr routers address.
some others commonly are 192.168.1.1
192.168.0.100
192.168.1.100

I think I was having a similar problem with my DAP-1522 ... FW Version 1.10 being used as an access point. I recently discovered that I was not able to connect to the configuration pages using a web browser by typing in it's IP address (192.168.0.50). When I originally set this up device up on my network, it worked just fine, but at some point in time, it stopped working. My solution to this problem was to set the switch on the back of the 1522 from Auto to AP, then re-boot the DAP-1522 by removing power, waiting 10 seconds, then plugging power back in. Once the AP re-booted, I was then able to access the configuration login page by typing 192.168.0.50 into my browser. My DAP-1522 access point is connected via port 1 to my D-link router, a DGL-4100, via a DGS-2208, 8 port gigabit switch. Hope this helps!

Hello, you need to set static addresses on your computer to access the 192.168.0.50.

Connection your wireless router to you computer with a cable.
go to control panel ->network connection and properties on your cable connections.

choose tcp/ip protocol and click properties


Set IP 192.168.0.50 and mask like the picture.

click ok and ok.
go to your webbrowser and try 192.168.0.50 does it work ?

use only IE 7 or greater with Java enabled.
remove any protection against Java you can have on your PC.

be sure to be on same subnet if you want to connect with access point and configure it.
Let me know if you now how to configure your IP address to be on same subnet.

It sounds as if you want to use your access point to connect into a wireless network. A typical, simple wireless network includes (1) access points and (2) clients such as a wireless card in your laptop. Access points can only communicate with clients and clients only communicate with APs. However, many access points can be configured to be clients. Usually you would find that in the basic wireless setup page. I don't know if the DWL-2000AP can be set up that way, but you can check in the manual. If it can, then you would select that mode, then specify the SSID of the network you want to join.

I don't know what you mean about 'so that default ip address is require', however to access your router/access point, the default address should be 192.168.0.1 for your routers configuration site, which you would type into your internet browser (internet explorer).

If it is not set at 192.168.0.1 for any reason, go to start>run>cmd and then OK. In the command prompt, type in "ipconfig". It will list you some addresses, Default Gateway would be the address to your router settings, enter that one into your browser.

The default IP address for the DWL-2000APis 192.168.0.50

You must be in the same subnet as your device in order to configure it. If you are in the 192.168.1.0 subnet, change your IP address on your computer to the 192.168.0.0 subnet. Assign yourself a static in that subnet with the last octet between 1 and 254, but not 50. I use 192.168.0.250, but any unused IP address in that subnet will do. Once you are in the same subnet, you should be able to reach your AP. If you still can't get to the http interface, then go to plan B: Your access point came with a CD: D-Link AirPlus Xtreme G AP Manager that provides an alternate client interface. You can setup security and change the password, and SSID using the client interface software if your http connection does not do it for you. Once you change your IP to the 192.168.1.0 subnet (which I assume you intend as it sounds like that is your LAN subnet), give the AP the gateway address of your router's IP address, and change your IP address back to whatever it was on your computer.

No, you can't download the needed programs to do so.

ok now connect the laptop thruh lan and try to open router configuration...check ther wther ur wireless is on.....or try to reset your router ...and cross your laptop with othr router,reply

Here you do not find support for illegal activity.
WEP keys are used to protect privacy and I do not see any valid reason why someone would like to crack into a protected connection.

Try 192.168.0.1 or 192.168.1.1

Verifying your network security isn't a trivial task.

Although WEP has some know vulnerabilities which can be exploited WPA is significantly stronger, and can generally only be broken by brute force password cracking or other nefarious means.

You have not indicated your operating system however the following web page has numerous links and descriptions of some of the software available for Unix and Windows

http://www.windowsecurity.com/whitepapers/Wireless-Cracking-Tools.html

be sure to check every point on this TIP
to connect to "prescribed site" (I assume the default router IP address 192.168.0.1) you must be on same subnet and connect using a cable to router.
Consult Quick install Guide
or follow user manual Page !0 instructions:
First, disable the Access the Internet using a proxy server function. To disable this function, go to Control Panel > Internet Options > Connections > LAN Settings and uncheck the enable box.
Open your web browser program such as Internet Explorer. Type the IP address of the DWL-2100AP in the address field (http://192.168.0.50) and press Enter. Make sure that the IP addresses of the
DWL-2100AP and your computer are in the same subnet.

If you need help in the matter let me know and I'll send you instructions

Try swith a differnet PSU ?