20 Most Recent Dell TrueMobile 2300 Wireless Broadband Router (TM23001) - Page 3 Questions & Answers

Those will be found in your operating manual. Just search for "default" and you'll find them. I've never seen a wireless router that had wireless encryption on by default, so none had a default key.

Dell™TrueMobile™2300 Wireless Broadband Router
User's Guide

http://support.dell.com/support/edocs/network/p57205/en/index.htm

This can very well be the case. The Dell TrueMobile 2300 Wireless Broadband Router is an 802.11b/g wireless access point, which means it operates in the 2.4 GHz spectrum. This is the same frequency that normal cordless phones and microwaves utilize.

See also this solution I posted regarding low signal strength.

There are two other ways to avoid interference. You can either change your network to the newer 802.11n standard or exchange your cordless phone to a system that operates in the 5.8 GHz range. I personally went the second way some time ago, because it was less expensive to buy a new phone system (good ones cost ~ 50$) than to exchange my router and all wireless network cards (~ 150$).

If you have any more questions, just come back here and leave a comment - I'm happy to help.

"Network settings" is a very broad term. I have to assume you don't have a manual to refer to to find the setting you need to change. Use this link to see the entire user's guide...
http://support.dell.com/support/edocs/network/p57205/en/index.htm

You need to get into the ip address of the router's settings and assign a static ip address to the specific hardware you are trying to connect. Most routers use some combination of 192.168.x.x where the x is a combination of either 1 or 0. Check with the router manufacturer to find the correct ip address. Good Luck

Just a note, you don't have high latency its just the server thinks you have high latency because its pinging you and your not pinging back because your ports aren't forwarded. The site linked below will guide you through the forwarding process, but please note! You can only host on one computer in your network, the reason for this is you can only port forward any port to one computer in your network.

It is important to follow everything this guide says for your port forwarding to be successful.
Please follow the guide on this site right here


If your having troubles understanding this guide, please leave a comment and I'll get back to you =)

Make sure the router is set to "gateway" mode and not "router" mode.

Mismatched power supply, bad AC outlet, and/or dead router.
If under warranty, get a return authorization.

Temporarily plug in wire network cable into Dell and log into Dell.
1. Set wireless up the same as the Belkin. Save these settings.
2. Set WAN to "Static IP Address and give it an address about 25 higher than Belkin. (Belkin 192.169.0.1 - Del 192.168.0.26). Save these settings.
3. Disable DHCP and Save these settings.
Exit web browser and disconnect network cable. Restart your complete system, first the Belkin, then the Dell, then your computers.
This way, the Belkin is running and able to assign IP addresses to all that start after it.

you need to change dhcp from the modem to the router to be a different network than what your router hands out via dhcp. you will also need to set dns up in the router to forward to the upstream modem.

the WEP password is located on the label on the botom of your router. The WEP password prevents unotherize conecting to the network. If some one for example like your naber see your network and conects to but put in the wrong WEP they will not be able to use your internet.

Yes.

Just ensure you configure your new HP pc with the same security code and password you used on your old Dell.

Look on the back of the router.

Your WEP Key should be printed on a label. :o)

Hi there you can try this locate your router in your internet connections and rightclick on it and look for repair and click on it now the comoputer will try to renew the ipconfiguration and address and hopefully this will get you going again once it is done you should be able to go to the router and click status and see if it says aquiring network address and wait to see if it does ok please let me know how this goes for you
regards mike

Well dell has ther online chat support team which is only avalibe intell 5 PM during the day only.

Press the Reset
button for about 10 seconds to reset the router to the defaults,
then use the default user name and password (admin and admin) to access the
Router Setup utility.

I turned off everything overnight, turned it back on in the morning, "WALLA" like magic everything worked. Thanks

Enabling the WEP for the Dell TrueMobile 2300 Wireless Router

Click the Start button.

Click All Programs.

Click Internet Explorer.
The Internet Explorer browser window appears.

Type the following in the Address line:
192.168.2.1

Click the Go button.
You are prompted for a Username and Password.

Type the following as your username:
admin

Type the following as your password:
admin

NOTE: If you previously changed your administrator password in the advanced settings of the router you will need type the password that you set.


Click the OK button.
The Dell TrueMobile Setup Page appears.

Click the Basic Settings tab.

Click the Wireless Security button on the left side of the page.
The Wireless Security window will appear.

For the highest level of security choose the 128 Bit encryption option.
You will have to type a name for your encryption key in the field to the left of the 128 Bit option.

Click the Save and Restart button on the left hand side of the page.
The Save and Restart window appears.

Click the Save and Restart button.
Your settings will be saved to the router.
More Secure
Configure the 2300 Wireless Router for WPA-PSK with TKIP Encryption.

Double-click on Internet Explorer.
The Internet Explorer window appears.
In the Address Bar type my.router or the default IP address 192.168.2.1.
Press the <Enter> key or click Go.
The TrueMobile 2300 password window appears.
Type the User Name and Password.
NOTE: The default user name is admin and the default password is admin.


Click OK.
The TrueMobile 2300 Wireless Router configuration window appears.
Click Basic Settings.
Click Wireless Security in the left-hand pane.
Click to select Enable Wireless Security.
Under Network Authentication, select WPA (Wireless Protected Access) from the drop-down menu.
Input a network key or password in the field to the right of WPA Pre-Shared Key.
NOTE: Your network key or password can use 8 to 64 characters using Hexadecimal digits or 8 to 63 characters using ASCII characters.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe
I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Before you throw it, save all the settings in router and try a re-start or there is normally a re-set button somewhere to press and set it back to factory settings. If the wireless re starts re-load previous settings. Please rate solution.

make sure that you are not connected both wirelessly and wired to one of the pc's, dissable the wired ethernet cards on all of the pc's as this may be the problem, and check in the DHCP client list in your router, refresh the list if you are able and see if there are two references to one pc with the same ip address. 

 

assuming you have DHCP enabled on the router this should not happen as long as your wireless adapters are set to obtain an ip address automatically.