20 Most Recent
Hotpoint-Ariston SDL510P Dishwasher - Page 5 Questions & Answers
Ariston dishwasher LFB 5B010 EX on/off, rinse aid and salt lights are flashing, left washing light orange and green (end) light on without flashing.
It sounds like there may be a problem with your Ariston dishwasher. The flashing lights and the dishwasher's inability to wash could be caused by a number of issues, including a problem with the control panel, a faulty water inlet valve, or a clogged wash pump.
To troubleshoot the issue, you can try the following steps:
- Check the control panel for any loose or damaged wires. If you find any loose or damaged wires, try to secure them or repair them as needed.
- Check the water inlet valve to make sure it is not clogged or faulty. The water inlet valve controls the flow of water into the dishwasher. If it is clogged or faulty, it could cause the dishwasher to stop working.
- Check the wash pump for any blockages. The wash pump is responsible for circulating the water during the wash cycle. If it is clogged, it could prevent the dishwasher from washing properly.
7/28/2023 8:00:37 PM •
Dishwashers
•
Answered
on Jul 28, 2023
Klarstein Dishwasher (Amazonia) when turned ON display cycles through the options, and buttons are unresponsive
If your Klarstein dishwasher is cycling through the display options and buttons are unresponsive, it is possible that there is an issue with the control board. Here are a few steps you can take to try and resolve the issue:
- Unplug the dishwasher from the power source for at least 5 minutes, then plug it back in and see if the issue persists.
- Check the dishwasher's circuit breaker or fuse box to make sure that power is being supplied to the unit.
- Inspect the control board for any visible signs of damage, such as burn marks or corrosion. If you find any damage, the control board may need to be replaced.
- If you are comfortable working with electronics, you can try resetting the control board by unplugging the dishwasher, removing the control board, and disconnecting the ribbon cables. Leave everything disconnected for a few minutes, then reassemble and reconnect everything.
If none of these steps resolve the issue, it may be necessary to contact a professional appliance repair service for further assistance.
7/26/2023 9:49:48 PM •
Dishwashers
•
Answered
on Jul 26, 2023
Dry light stays on all the time and dishwasher kitchen aid model kuds301xbl4 won't run
If the "Dry" light stays on all the time on your KitchenAid dishwasher model KUDS301XBL4 and the dishwasher won't run, there may be a few potential causes for this issue. Here are some troubleshooting steps you can take:
- Check the control panel: Inspect the control panel of the dishwasher for any buttons that may be stuck or not responding properly. Press each button to ensure they are engaging properly and not stuck in a pressed position. If you notice any issues with the control panel, it may need to be repaired or replaced.
- Reset the dishwasher: Turn off the dishwasher and unplug it from the power outlet. Leave it unplugged for a few minutes to allow any residual power to dissipate. Then, plug it back in and try turning it on again. This can help reset the dishwasher's control board and clear any temporary issues.
- Verify the door latch: Ensure that the dishwasher door is fully closed and securely latched. If the door is not closed properly, the dishwasher may not start. Check for any obstructions or debris around the door latch and clean it if necessary. If the latch is damaged or not functioning correctly, it may need to be repaired or replaced.
- Check the water supply: Confirm that the water supply to the dishwasher is turned on and there are no clogs or restrictions in the water inlet valve or hoses. Make sure the water pressure is sufficient for the dishwasher to operate properly.
- Examine the heating element: The "Dry" light staying on could indicate a problem with the dishwasher's heating element. Inspect the heating element for any visible signs of damage or malfunction. If the heating element is faulty, it may need to be replaced by contacting the manufacturer or an authorized service center.
- Contact customer support: If none of the above steps resolve the issue, it is recommended to contact KitchenAid customer support or an authorized service center for further assistance. Provide them with details about the problem and any troubleshooting steps you have already taken. They may be able to offer additional guidance or suggest further troubleshooting or repairs.
7/2/2023 2:11:34 PM •
Dishwashers
•
Answered
on Jul 02, 2023
Not finding what you are looking for?