20 Most Recent King Kutter Rotary Tiller Pto Bush Hog John Deere Long - Page 6 Questions & Answers

https://www.mikestools.com/ownersmanuals/DeltaScrollSaws/40-150.pdf this is Delta's version of the same saw's manual. Hopefully anyone who still needs this will find it faster than I did!

This is usually due to the contact for the stop button not working. Normally, the message "Pin Code Expired" is replaced by "Enter Pin code" when you press the stop button to access the keyboard. If the stop button doesn't work, the mower thinks the keyboard cover is still closed and therefore continues to display "Pin code expired".Open the large lid (the one that gives access to the mowing height selector) and look near the stop button, there's a small rectangular thing connected to a wire and held in place with a metal clip. Take off the clip with some flat object like a screwdriver, then take out the rectangular thing, which has a tiny button on it. Press the button a few times to unstick it. You should now see "Enter pin code" on the screen. Put everything back the way it was, and you should be all set.By the way, I know this question was posted in 2010, I'm posting the reply to help others googling for this question. I saw some people actually had their motherboard replaced unnecessarily for this simple problem!

Leave fuel cap off and filter submerged. Ether fish out the fuel return or at least position where it's visible. Then press the purge bulb several times. Fuel should spurt out the return. If no fuel from return line and air bubbles come from filter, lines are reversed somewhere.

1. Place the Pergola structure onto a flat surface in an area with adequate space for assembly and use. 2. Unwrap the hardware bag (included with the pergola) and place the contents on the flat surface near the structure. 3. Begin the assembly by attaching one of the long side rails to the top of the Pergola. Insert the rail into the slot at the top of the structure. Securing it with the provided hardware. Tighten the four screws using a drill to firmly secure the rail in place. 4. Next attach the second long side rail in the same fashion. 5. With both side rails firmly in place, attach the short side rails. Insert the rail into the slot at the top of the structure and then secure it with the provided hardware. Tighten the screws using a drill to firmly secure the rail in place. 6. Repeat this same process to attach the remaining short side rail. 7. Attach the four corner brackets using the provided lag bolts and washers. Some models may require different hardware for this step. 8. Secure the corner brackets with the provided bolts and washers. 9. Attach the remaining lag bolts into the holes in the top of the Pergola frame. 10. Tighten all the screws and bolts using a drill which will secure the frame in place. 11. Place the canopy (sold separately) on the top of the Pergola frame and secure it using the provided hardware and tools. 12. Once the canopy is secured in place.

Here are some possible causes and solutions: Belt Issues: If the drive belt is broken or loose, the tines won't turn. Check the belt tension and replace the belt if necessary . Idler Assembly: If the idler assembly is not properly tensioning the drive belt, the tines won't turn. Adjust the idler assembly or replace it if necessary . Engagement Cable: If the engagement cable is loose or not tensioned properly, it may need to be tightened or replaced altogether . Transmission Issues: If there is an issue with the transmission, such as a broken gear, the tines won't turn. Stop using the machine immediately and inspect the transmission . Since you mentioned that your tiller tines were turning fast after replacing the carburetor and then stopped turning after connecting the throttle cable, it's possible that there is an issue with the engagement cable. You may want to check if it's properly tensioned and connected to ensure that it's not causing any issues How To Fix Tines That Will Not Move - Tiller Repair

Typical carburetor low speed circuit is blocked but can be fuel or other. Likely needs carb adjust, clean and/or rebuild.

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwjF7pm4xpSCAxVEmIkEHaPbAvoQFnoECB0QAQ&url=https%3A%2F%2Fwww.orangetractortalks.com%2Fforums%2Fthreads%2Fcan-i-determine-what-model-year-from-serial-code.45724%2F&usg=AOvVaw320X8niJs2M0dRBU5lxjT6&opi=89978449

look up your model for the manual ------- https://www.mountfieldlawnmowers.co.uk/support

Likely insufficient battery voltage. Test battery and charging system.

Generic parts made in China. https://www.google.com/search?q=Replacement+swivel+base+for+Wilson+Fisher+Glider+Chair ..

This may help: How to Clear Codes On A John Deere Skid Steer ' Pap? Machinery (papemachinery.com) John Deere 310SL Backhoe Loader Diagnostic & Test Service Manual (TM13297X19) ' A++ Repair Manual Store (aplusmanual.com)

8us fl oz= 0.2365882L the following link is conversion of oz to liters US Fluid Ounces to Liters conversion

A liter is about 35.20 UK ounces or about 33.81 US ounces.

The solenoid should have three posts. Two large contactor lugs and a smaller terminal for control (batt pos). The solenoid frame must be securely attached to the mower chassis as it is the control winding return path (batt neg).

The large gauge red wire from the positive battery post and 2 smaller red wires stack on to one contactor lug (post 1). The other large gauge red wire from the starter goes to the other contactor lug (post 2). The small yellow wire goes to the smaller solenoid control terminal (center post) and energizes the relay with battery positive from the ignition switch S (start) terminal.

Refer to attachment, wiring diagram.

The exact same thing happened to me. I was about to bring it back to the store, but was able to figure it out. The black frame that holds the bag has two bolts that screw in at the bottom. Look for the black nobs. Unscrew both, pull the frame out 8 inches until it lines up with the new hole and insert screws and tighten. Cord will then pull normally. I have no idea why they do this and it's not in the manual, but there was a confusing sign on the engine that illustrates this procedure. Annoying, but an easy fix.

Will crank over but does not turn on what could it be?

I'm having the same issue.

Tanalized pressure treated cedar Joe. It looks nice, smells great and holds up well in the weather. If you don't stain it, the finish will go a soft grey, and if you want to bring it back, you can pressure wash it. Larch if you can get it, comes second. My waterwheel in England was cast iron, but the timber was Larch, and it lasted really well. I hope you are doing well Joe and as it is Thanksgiving weekend in Canada, I will wish you a good one in advance! ..

What are you working on?

Impossible to answer as you don't say on what?? So we will just guess. Google make model carburetor solenoid wiring diagram https://www.google.com/search?q=%E2%80%8Bmake+model+carburetor+solenoid+wiring+diagram ..