Karcher A2554 ME Canister WetDry Vacuum - Answered Questions & Fixed issues

If twisting, pulling, and pushing are not working, then you may need to use some pliers to help loosen up the connection. You could also try wrapping the connection with a cloth or rag and applying pressure with a pair of pliers. If that still doesn't work, you may need to cut the connection and replace it with a new one.

1. Blocked hose: Check the hose for any blockages or kinks that may be preventing air flow. If the hose is blocked, clear it out and try the vacuum again.
2. Damaged impeller: The impeller is the component of the vacuum that creates the suction. If it's damaged or worn, it may not be able to generate enough suction. If this is the case, you'll need to replace the impeller.
3. Damaged motor: If the motor is not functioning properly, it may not be able to generate enough suction. If this is the case, you'll need to replace the motor.
4. Clogged or worn out turbine: The turbine is responsible for moving air through the vacuum. If it's clogged or worn out, it may not be able to generate enough suction. If this is the case, you'll need to replace the turbine.
5. Broken or disconnected hose connection: Check the connections between the hose and the vacuum to make sure they are secure and not broken.
6. Faulty switch: If the switch that turns the vacuum on and off is faulty, it may not be allowing the vacuum to run. If this is the case, you'll need to replace the switch.

It sounds like you are having some issues with your Karcher Puzzi 10/1 carpet and upholstery cleaning machine. Here are a few things you can try to troubleshoot the problem:

1. Make sure that the hose is securely attached to the machine and that there are no kinks or blockages in the hose.
2. Check the filter to make sure it is clean and not clogged. If the filter is dirty or clogged, it can reduce suction power.
3. Check the solution tank to make sure it is properly seated and sealed. If the solution tank is not seated correctly, it can cause problems with suction.
4. Make sure that the machine is turned on and that the switch is set to the "suction" mode.
5. If the problem persists, you may need to take the machine to a Karcher service center for further diagnosis and repair.

I hope this helps! Let me know if you have any other questions.

The motor has a fan on the top to cool it off and it is usually pressed on the shaft, they can come loose. The impellor on the motor may have come loose, there may be something stuck in the impellor area. Some of the motors have pressed on parts and cannot be repaired.

Hello you need to search in google,bing ect search engine. I did search but not found

Possibly water went into the motor are a new motor will now be required. Either way the motor sounds past its best.

replace piston seals and valves.

Check the hoses for clogs due carpet fibers.

there should be a labeled fill line on the clean water resavore

Get under it with something like a butter knife and lift with the knife while you turn it.

spinac on -of ist ok

karcher K6.80 how 2 repair

Clean and check the vacuum motor for accumulated jam objects, dirt and dust. Use a small paint brush and if necessary apply some oil or grease in mechanical part. Be sure that the filter bag is clean also.Regularly clean it and you'll assure the vacuum will performed well.
Thanks for asking.

Most likely the hose pipe has nothing to do with the problem. Most likely is a loose connection and as time goes by the connection gets looser, which causes failure rate to increase. Once until is on, the power flowing through the loose connection helps keeps it connected. Open the unit and wiggle this and that until to can isolate the actual cause of the problem. Try not to shock yourself.

If you have not yet found a solution, then here are some steps to take.
1. The soap dispenser only works on low pressure!!!!!!! So you have to REMOVE the high pressure Sprayer so that all you use is the Trigger Gun without the Extender.
2. Pull out the thin Plastic Hose with the filter attached in the end, and insert into your container of detergent.
It will only splatter the detergent over the area you want to clean, so you will then need to REATTACH the SPRAYER into the hand gun to work with the soap to lather, clean and spray of till clean.
This seems to be the way the system works on this model......also known as K2.36M (AU) in Australia or (EU) in Europe on the Karcher.com.au site then Service then Manuals. or on the link below.
Hope this helps any of you who has misplaced their Owners Manual just like I did and had a great problem trying to find a link as Karcher doesn't recognize the Model No: as Winner 10 or 11.

Cheers, Luke

That would depend on the make and model of the steamer.

Replace the part that is faulty. Here is the parts lists. https://www.google.com/search?q=Bissell+1713+Crosswave+parts+diagram ..

To turn off the LED service light on your Aerus CentraLux central vacuum model E130J after replacing the motor, switch the blue box on the circuit board from "ON" to "MEDI."

Alot depends on the type of hose. There are plastic hoses and rubber hoses. Generally you can use a smaller plastic connector to connect two rubber hoses together and visa versa, Make sure it is a snug fix. You could also use an adhesive to keep it together.