20 Most Recent Fisher and Paykel Aquasmart wl80t65c - Page 4 Questions & Answers


AquaSmart Error codes

ed78e139-4f23-43cb-9d7c-9b9675d7f898.jpg

Fisher and... | Answered on Dec 14, 2013


50.(00110010) Hot Valve Coil Faulty
The Motor Control Module has measured a voltage from the valve diagnostic circuit that indicates the hot valve is faulty. The most likely cause is that the valve harness has not
been connected correctly or the valve is open circuit. See fault 48 for service procedure.
48. (00110000) Hot and Cold Valve Coil Faulty
The Motor Controller module has measured voltages from the valve diagnostic circuit that
indicate both the hot and cold valves are faulty. The most likely cause is that the valve harnesses have not been connected correctly or the valve is open circuit.
Primary Source: Wiring.
Action: Check the valve harnesses are correctly fastened to the valves or the
pins are not bent backwards.
Secondary Source: Water Valves.
Action: Check the valve coils are not faulty (open circuit).
Tertiary Source: Motor Controller module.
Action: Replace the Motor Controller module.

Fisher and... | Answered on Dec 13, 2013


Suspension damper rods need replacing at the same time as bands.

Fisher and... | Answered on Dec 13, 2013


cold valve fault. check the water supply, check the valves. otherwise it's the motor controller. replace parts as necessary.

Fisher and... | Answered on Dec 11, 2013


cold water valve fault. often caused by the motor controller failing. test valve during fill for 24V recieved. if not, motor controller needs replacing.

Fisher and... | Answered on Dec 11, 2013


there is no filter to clean on these machines.

Fisher and... | Answered on Dec 10, 2013


Have you taken the lid off and looked at the operation whilst going through the self cleaning cycle? Have you checked that the hoses, i.e. clips, are secure? Have you checked for cracking in the hoses? If it is not evident have you tried tying kitchen towel round hoses? Have you cleaned the filter out?

Fisher and... | Answered on Nov 18, 2013


my problem is I did two wash and then I put two thin curtain in to wash and that is when I had this problem

Fisher and... | Answered on Aug 13, 2013


Unless there's damage to the machine it is the load. Make sure you aren't washing to small of a load. People do not realize how fast washers spin to extract. Just like they use tiny weights to balance your car tire, it only takes a little bit of weight to unbalance it.

Fisher and... | Answered on May 02, 2013


It's a motherboard power supply issue.
Is your board part number IW SD11 420093
These boards have that problem. let me know.

Fisher and... | Answered on Feb 11, 2013


Hi your shaft may be bent,Or metal particles on the rotor magnets.
Get someone to turn the bowl & you look at the shaft without the rotor on & see if it's bent.

Fisher and... | Answered on Feb 10, 2013


Error code 245 is pump stall.
If the 1.6amp glass fuse has blown, the five mosfets on right side have shorted out there legs & blown the fuse.
Also check the pump drive parts for shorted legs.
There are three resistor that burn out near the fuse.
I will up loaded some pictures later.

2_9_2013_9_26_34_am.jpg


2_9_2013_9_26_58_am.jpg

Fisher and... | Answered on Feb 10, 2013

Not finding what you are looking for?
Fisher and Paykel Aquasmart wl80t65c Logo

121 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fisher and Paykel Washing Machines

  • Fisher and Paykel Washing Machines

Most Popular Question

fisher paykel top loading washing

  • Washing Machines
Loading...