20 Most Recent Fisher and Paykel Aquasmart wl80t65c - Page 2 Questions & Answers


Hi! Have you completed a "Clean Up" cycle? It should prompt you every 100 washes to do a clean up - it should be under the "Lifestyle" menu. When you do it, I suggest you use OXY soaker (1 whole Cup) instead of normal detergent and make sure it is all HOT water. It soaks for 4 hours, but is very good at cleaning the bowl and workings to stop brown marks on your clothes and towels

Fisher and... | Answered on Oct 10, 2014


Did you look up your manual to help with the problem?

AquaSmart2 8kg - this is a link to download your manual

The good thing is that if you got Fisher & Paykel to come out, they offer a warranty on their service - so call them again and tell them the situation - they should come out for free....

Fisher and... | Answered on Sep 18, 2014


If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Fisher and... | Answered on Aug 17, 2014


The LCD may have failed but also it could be failure of the display controller.

Fisher and... | Answered on Jul 17, 2014


This model has a sensor, so the water comes on and off till it senses the right amount. If it is in water saving mode, then there will be no sitting water..... maybe you can give more details of the problem. Good Luck!

Fisher and... | Answered on Jun 11, 2014


Did you do a size adjustment for the boards.

oufptf0cczcwaaca2etkveu72ce464vpyolttf0c0zcwaacaceuyzaft5t7is31fvqmgz2y0aaaaairibaaaaaaqirebaaaaqijebgaaaaahehsaaaaahehsaaaaabaisqeaaabaimqgaaaaacesgwaaaacesgwaaaaaeckxaqaaaecixayaaaaairibaaaaairibaaaaaaqirebaaaaqijebgaaaaahehsaaaaahehsaaaaabaisqeaaabaimqgaaaaacesgwaaaacesgwaaaaaeckxaqaaaedip7vnyrypuayxaaaaaelftksuqmcc
03703acf-29ae-4d58-856e-e9342f74f93a.jpg

Fisher and... | Answered on May 18, 2014


The most common problem with AquaSmart is the pump.
The pump has gone bad and blown the motor controller board.
Some AquaSmart machines display the wrong Error code (49)
witch is not the correct code for this problem.
Pump and motor controller board need replacing.
Maybe cheaper to buy a good secondhand machine.

Fisher and... | Answered on May 18, 2014


Is it plugged in to an outlet? Is there power to the outlet?

Fisher and... | Answered on May 18, 2014


Fisher& Paykel have a lot of controls. But if it's filled with water and the lights are on, you have power to the unit. Try unplugging it, waif 5 min. Power it up advance the setting to drain/ spin setting with the door closed and try it again. What do you mean the spanner ?

Fisher and... | Answered on May 15, 2014


Sounds like motor brushes not making contact.

Fisher and... | Answered on Mar 07, 2014


Have you removed the inner bowl and check under pump cover ,if so have youput the cover on around th correct way.Is the flapper inside housing of pump obstructed.

Fisher and... | Answered on Mar 07, 2014


what are you wanting to clean?? most places are the pump & bowl under the agitator..

the pump is under the machine, some have a little plastic side hatch you open to get to the pump.

the bow is gotten to but removing the agitator, usually a thumb nut down the middle of agitator, and then pull up agitator to remove out the top,

soak up all the water & clean out the dirt & scale you find.

Fisher and... | Answered on Feb 20, 2014


In the AquaSmart machines the pump over currents and blows the water valves fuse 1.6 Amp glass, The motor controller board
would be faulty as well and need repair.
49. (00110001) Cold Valve or Cold Valve & Hot Valve Faulty
The Motor Control Module has measured a voltage from the valve diagnostic circuit that
indicates the cold valve or both the cold and hot valve is faulty. The most likely cause is
that the valve harness has not been connected correctly or the valve(s) is open circuit.
Primary Source: Wiring.
Action: Check the valve harnesses are correctly fastened to the valves and
the motor control module or the pins are not bent backwards.
Secondary Source: Water Valves.
Action: Measure the resistance of the cold and hot valve coils.
Tertiary Source: Motor Control module.
Action: Replace the Motor Control module.

Fisher and... | Answered on Jan 08, 2014

Not finding what you are looking for?
Fisher and Paykel Aquasmart wl80t65c Logo

121 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fisher and Paykel Washing Machines

  • Fisher and Paykel Washing Machines

Most Popular Question

fisher paykel top loading washing

  • Washing Machines
Loading...