Lanier LF310 - Page 6 - Answered Questions & Fixed issues
I have a lanier
Remove your printer from the PC and uninstall the printer software. make sure there is no other conflicting softwares in the pc specially recently downloaded programs. If so uninstall them too. Now reinstall the printer software and connect the Printer to be detected and installed. Check printer properties to see the ink levels.
Now make a test to see if the PC commands the printer. If there is no response, check the head assembly/ ink carriage to be struck or out of alignment. Check for possible realignment of any of these mechanical problems., jammed roller or head drive
If the catridges were removed make sure they are in place . If you are removing them make sure that the printer is shut off .
If none work it can also be an error inthe main board. Need to swap one to confirm
We are going to get rid of our lanier 6540 and
To be absolutely sure no personal info is stored you should remove the harddrive and either destroy it or have cleaned by a professional service. You can do it yourself with a few rare earth magnets.
How to enter service mode on a lanier ld225
Press Clear/Modes, then 107, then press AND HOLD Clear/Stop
This will get you into the service mode screen.
Know what you are doing before going into any modes and changing anything.
Good Luck and Thank You for using Fixya
7/20/2010 11:01:18 PM •
Lanier Office...
•
Answered
on Jul 20, 2010
•
1,560 views
Lanier copier ld425csp screen froze
Lanier and Ricoh have been having a huge problem with their touch screens going bad. If you have a service contract on your copier, you should be able to get it replaced for free under the warranty.
In the meantime, try turning the machine off and back on, and you might be able to get it working temporarily.
Showing error message sc541
this is an error for the fuser the thermistors have not registered the temps properly check the fuser and if you know how to take it apart clean the thermistors.. you could try an sc reset using the following proceedure...Yellow clear button then 107 then hold down the stop button..wait for the screen to change to show copier sp turn off the machine and wait 5 secs then turn off. If this doesnt reset do the same proceedure on the copier sp enter this then look for mode 5. enter this mode and look for 810 sc reset and set this then turn off wait and turn back on....if this error occurs regularly the thermistors will have to be changed.. hope this helps..A
When printing paper gets stuck. Not rolling thourh
LANIER COPIER PROBLEM SIMILAR TO RICOH COPIER PROBLEM AND IF THE PAPER GOT STUCK ,FIRST YOU MUST SEE AT WHICH
LEVEL/IS IT CRUMBLEB OR JUST MESHED THROUGH OR JUST UNABLE TO PASSED OUT FROM TRAY.
IF PASSED OUT FROM TRAY BUT STUCK AT DUPLEX AREA ,THAT MEANS YOUR FINGER AND MYLAR/RUBBER ROLLER MUST BENDED OR NO GRIP SO YOU HAVE TO REPLACED IT.
IF STUCK FROM THE TRAY, EITHER YOU DID NOT NOT " FAN" THE PAPER BEFORE USE AS NO AIR BETWEEN THE PAPAERSOR HAVE TO REPLACE THE PAD AND UPLIFT ROLLER RUBBER[1 PIECE ONLY PER TRAY]
IF STUCK AT FUSER AREA,JUST CHECK THE UPPER & LOWER ROLLER, THERE SHOULD BE THE ROLLERS NOT MEET TOGETHER. NEE MORE CLARIFICATION
Copies are shaded and have a solid black line down
Is this an analog or digital copier?
Multiple things could cause what you describe.
To answer your question rubber rollers can be cleaned with soap and water and a damp cloth.
Hot rollers cannot be cleaned and should be replaced as the teflon coating has failed.
Organic drums should not be cleaned with a cleaner but just a clean dry cloth.
I would look at your mirrors(under the glass) if there is dust on them it will darken your copies and could cause lines.
If it is digital print out a counter if it is a good print the your problem is dirty mirrors and / glass
Lanier LD135. How do I program it to print
Envelopes thru bypass only....once they are set youl need to set the bypass to envelopes at the machine either thru user tools or by pressing bypass then the # key and selecting envelope or custom size and entering the size of your envelopes.
Back at the computer go into print proprties and select paper souce bypass the printdriver will use the machine settings unless ou tell it otherwise
SC 571 error
Hello sir; The error code you have display, its means the fuser oil waste bottle full, check it out and dump it out, otherwise that's senser problem.
I purchased a Lanier 5435 at a garage sale here at
Hello sir; There have foer part to be separet; 1, auto doccument feeder. 2, machine body , 3 base, 4 finisher. Now let's separet finisher; open the finisher door, on the right hand side first screw lock the cross bar, unscrew it ,pull out cross bar move finisher away, next to remove ADF lift up ADF you can see two big hinge, unscrew it and remove it ,nex to separet body and base;on the back cover of the machine on the lower left have a small cover with one screw on it release open it out you will see the connector, disconnect it, now pull out the second tray there have a screw inside the bottom screw the body and base together, unscrew it next remove the plastic strip between the front door and 1st paper tray, you will see two handle , good luck !!!
Not finding what you are looking for?