Top 20 Lanier LF310 - Page 8 Questions & Answers

Check the paper transport motor,trnsport clutch or sensors.

If it is new call a local dealer to see if they can fix it.
If it is old, the machine might be out of service life. Tryto get a 3rd party service repair person to see if the person can repair the machine.

Hello sir; You just press "user mode' it will show up "total count"

Hello sir; Please contact with me I can get for you, 973-533 6778

Clean the paper feder rollers to use izopropilic alcool.

Hello sir; Pull out the paper tray ,check the paper senser is moving freely,clean the paper pick up roller, it will take care the problem.

tHE sC 40 xx CODE TO REFER THE FAN SUCTION MOTORS.

If paper is loaded in the portrait orientation, 8 1/2 x 11 paper...32 cpm.

The transfer belts on these generaly cant be cleaned if you know how you can just remove the transfer belt unit and take the cleaning unit ou this is positioned on teh leaft hand side just under the belt at the top there is screw take this out then press the small brown lever and and pull teh unit out carefully make sure you press the lever in as jif you dont you can damage the belt..vac this out and wipe the blade with a soft dry cloth.. if you are savy with the machine the main area to clean is the alloy or chrome roller at the top.. you will have to take the belt off to clean this.. the id sensors read off this to get reg and colour calibration right so it coulld cause problems if this is dirty..let me know if this helps or if you need more info..Good Luck A

Make sure that all the paper trays have the correct size and direction (portrait or landscape) in both the copier and print driver.

Try thru the doc feed, or if off the glass special original might help. -Carl

Open the machine and to the right under the drum you should see the the black powder (toner) going down into container the right lower side  cover must come off. probably a service call will be needed

open right cover, and front cover. Remove toner bottle assembly (not just bottle), unplug drum (photoconductor) connector. Press the gray/silver release tab and slide out drum. Install and plug in new unit, replace toner assembly, close covers, and the new unit is automatically detected and calibration will begin.

Hello sir; According the menual said, that's thermister open or power supply board, but before go that far why don't try to do a reset, steps as follow;
Press "clear mode", "107", then pres and hold down "clear/stop" key, then choice "copier SP" then enter "5810" press enter, select 1, then press"R/#" key and "original type" key at same time to reset, try it and let me know the result. after reset just turn power off and back on.

No, you can't reset. You'll need a tech. Here's what the manual says: Symptom (SC101) - Exposure lamp error - The standard white level was not detected properly when scanning the white plate. Possible Cause: ? Exposure lamp defective ? Lamp stabilizer defective ? Exposure lamp connector defective ? Standard white plate dirty ? Scanner mirror or scanner lens out of position or dirty ? SBU defective

The polygon mirror motor (laser motor) is shot, and needs to be replaced.

Hi,

This error comes if you have the drivers curropted by some chance. Did you install any software recently that might have disturbed the drivers.

Please find the user manual and the link where you can download the drivers:

http://www.devicemanuals.com/guide/Multifunctional/Lanier/Lanier-LD015spf-Multifunction-Operating-Manual-==TVRReU5UVTE=.html

and

http://driverscollection.com/?H=LD015&By=Lanier

Thanks for contacting Fixya

A2 means something is wrong in the duplexer. Check all parts of the duplexer for jammed paper.

Try this press the "yellow/ca" botton, then enter 1-0-7, then press and hold the "red" stop" till the display changes. Once, it changes turn the Main power switch OFF. Not the one on the control pannel. Let it power down then turn it back ON. If the problem is still there try to turn the copier Off again and unplug the sorter/ finisher and turn the copier back ON. Is the problem gone, if so you may have to get a service person come in and repair the sorter. Good Luck.....

LD unit problem, or laser sync detector....requires a tech for sure.