KitchenAid KUDS30FXSS Builtin Dishwasher - Answered Questions & Fixed issues

it is likely the heater or thermostat are faulty. Try to run in short cycle like rinse which works on cold water.

Press the Cancel/ Drain cycle for a few seconds. The dishwasher should reset itself. See if this makes any difference. Also first turn the mains power to dishwasher off and back on.

Here's a link for the repair manual for your dishwasher: http://www.appliancerepair.net/kitchenaid-dishwasher-repair.html Concentration should be on Chapter 2 subsection 2-3 "No Fill" Then go to Chapter 6; subsections 6-2, 6-3, 6-3a, 6-3b, 6-3c, and 6-3h for testing procedures on relays, actuator valves, etc.

first ensure your machine is not set to half load, as this may only run the bottom shelf and not the top. also check the wather sprinkler rotor is not blocked. remove it and check the holes are free from debris.i hope this was useful

See my problem and solution. Sounds like you, too, are having a problem with the main control board (computer chip that controls the dishwasher), which is apparently a common problem with this model dishwasher. The part can be found here, for $211 (tax + shipping), and they have a 30-day return policy in the event that it does not fix the problem. It's an easy DIY fix. Hopefully this helps!

See my problem and solution. Sounds like you, too, are having a problem with the main control board (computer chip that controls the dishwasher), which is apparently a common problem with this model dishwasher. The part can be found here, for $211 (tax + shipping), and they have a 30-day return policy in the event that it does not fix the problem. It's an easy DIY fix. Hopefully this helps!

Sounds to me like a plumbing issue. Might have to try another plumber.

here is a link to installation copy and paste https://www.manualslib.com/manual/931286/Kitchenaid-Kgct305bwh0.html?page=2#manual

It sounds like the water inlet valve has stopped letting water in. With no water the spray bar won't rotate as it is driven by the pump. Generic videos.

Same issue here. WHAT WORKED FOR ME was simply unplugging the dishwasher for 15 seconds (no idea if 15s necessary), and plugging back in. Viola!

If the hole is small you can seal it with epoxy putty. Clean and abrade the area and after mixing the putty make sure it is pushed well into the hole and if possible smoothed over on the underside. Two types that will work.

J-B Weld Waterweld Epoxy Putty, 57-g ' Canadian Tire

https://www.canadiantire.ca > ... > Adhesives Waterweld Epoxy Putty allows you to make permanent repairs in moist or under water applications,Will fully cure in 60 minutes and will adhere to most ... Rating: 4.2 · ‎106 reviews

• J-B Weld SteelStik Epoxy Putty Stick, 57-g ' Canadian Tire

  https://www.canadiantire.ca > ... > Adhesives J-B Weld SteelStik Epoxy Putty is a steel-reinforced epoxy putty stick that is great for use on automotive and machine parts, exhaust systems, plumbing, .. ..

I couldn’t find any error code 2H but I did find an error code H2O. This code means insufficient water pressure. If the display reads 2H, it usually means the start delay function is turned on. The dishwasher will turn on in 2 hours if door is closed. This dishwasher is advanced. To understand all operations you should read the user guide or manual.

Do a hard reset and it should work..if not then replace the control board. http://www.ehow.com/how_7488137_reset-kud101flss6-dishwasher-control-lock.html

Question edited for clarity. Question moved from Miscellaneous. Create upward pressure as you are undoing it. You may be able to make it grip.

possible flood switch stuck

Try a Power Reset. Before you go to bed, cut the power to it using the breaker, the plug, or isolation switch. Try next dinner time. Press and Hold the On switch before you turn it back on to fully dissipate power. Other ideas https://www.google.com/search?q=KitchenAid+Superba+Monterey+21%2C+Model+KDSM-21A+not+pumping+out+at+the+end+of+the+cycle ..

I had this exact same story with my new Whirlpool dishwasher. My daughter fell on the open dishwasher door and afterwards it wouldn't latch closed. After researching online, I learned that 90% of the time it's bent door hinges. At $$130 each, $260 total, I didn't want to replace the hinges. So I removed the hinges, took them downstairs to my shop, put them in the vise and straightened them back with a hammer. Just took a few good, solid hits on each hinge and they were straight again. I installed them back onto the dishwasher and it worked like a charm! Door latches just fine.

The dispenser needle valve is not seating properly and correctly causing it to be rinsing and also the aid to be leaking out water.