20 Most Recent Linksys Wireless-G WRT54GS Router (e125894) - Page 4 Questions & Answers

If you are referring to the Administration password to change settings, you can't "find" it.
You can only reset the whole router and put in a new password.
To do so, hold in the tiny recessed RESET button on the back for a full 30 seconds and release.
Then log in to it from you browser at address 192.168.1.1 and use "admin" as the logon and "admin" as the password. This resets EVERYTHING in the whole router to factory settings.
Then you can set up security and a new password.

Good day,

You can use your Wireless Connection by enabling it in your router.
You can access your Linksys router by logging in to its webpage. Look at your routers manual for its default configuration in accessing your router.Most router use http://192.168.1.1 or http://192.168.0.1

Username:
Password:

Should appear in your browser refer to your manuals deafault Username and Password most Linksys routers use:

username:admin
password:admin

you can enable your wireless connections in wireless settings page and don't forget to put password for your wifi for security, you can use WEP, WPA etc. so that no one can steal your internet through your wireless connection.

Hello
Try updating the firmware on the router.You need to log into the router using 192.168.1.0

Username =admin
password = admin or the word password.

Once in the routers home page check for updates and download and install.Also be sure any firewalls are not blocking the signal.
While your in the router set up a personal wep key for your wireless security.
There is a possibility your lossing signal to outside intruder.

come to chat support again... i will fix the problem...

First, be sure that 192.168.1.1 is in fact the address of your router. Follow the following steps to confirm this information in windows.

1) Press the Windows key and "R" key simultaneously
2) Type "cmd" and press enter
3) Type "ipconfig" into the command prompt
4) The ip address following the label "Default Gateway" is the ip you should be entering into your web browser in order to access the router.

The default password for this model router is "admin" while the username is "admin". If these credentials do not allow you access to the router, someone has changed these settings without your knowledge.

Unfortunately, you can't find your Wireless Access Code of your router without knowing the password to access your router configuration. It is because, you can only see the Wireless Access Code by going to the router configuration page and in order to go to the router configuration page, you should know the router password.

You should reset your router to default. In order to do this, you can press the Reset button at the back of your router for 30 seconds. Then you can try to use the user name "admin" and password is "blank" or password or admin as well.

Here is a direct link to show you step by step how to secure you router, Simply copy and paste address into address bar of your browser.
http://homecommunity.cisco.com/t5/Wireless-Routers/Setting-up-a-secure-network-with-a-WRT54G/m-p/91479

Hi,No more worries, You can approach this http://www.thewebpole.com/ site's user friendly service ,here only i successfully launched my website with this site's domain name and hosting at very cheap rate.you too also do this one.All the best.

Linksys

Use the restart button on the back of the router and set it up again by connecting your computer to the router using and ethernet cable.

There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

you can watch this video to setup your linksys wrt54gs

Hello,
You can find all these information on your computer. Press Windows key + r (Win+r) you will get the run bar. Now type "cmd" and hit enter. You will get a black screen. In the black screen type "ipconfig /all" and hit enter. You will get all the details. Now while entering in your I pad you have to change only the IP add. For example..on your computer you have..
IP add: 192.168.2.4 Sub Net: 255.255.255.0 Default Gateway: 192.168.2.1 DNS. 4.2.2.2 4.2.2.3
In your I pad you will have to enter like this.. IP add: 192.168.2.15 Sub Net: 255.255.255.0 Default Gateway: 192.168.2.1 DNS. 4.2.2.2 4.2.2.3
So change the last number of IP address. Let it be anything above 15 and below 254.
Hope this helped.!

http://w0ry.home.bresnan.net/EchoLink/#Router

Take a look at this setup and see if you have all the right values for echolink.

This setup sounds pretty cool. You do internet stuff via radio eh?

First I assume that you simply posted this under "Linksys > WRT" by mistake and you are using a D-Link router.
How to set up the ports for Echolink:

1. Go to this page (link).
2. Choose the correct router model (almost at the end of the page)
3. skip the advertisement on the next page (upper right corner)
4. choose "Echolink" from the list.
5. Simply follow the instructions.
6. Voila!

In general: Make sure that your Windows Firewall is not blocking the application (see Control Panel -> Windows Firewall -> Exceptions) (details also here). You have to allow UDP destination ports 5198-5199 between Internet and PC in both directions and allow TCP (source port any, destination port 5200) from PC to Internet.

If you have any more questions, just come back and leave a comment - I am happy to help!

Connect your ethernet cable from your cabe modem to the port on the left

When first setting this up hardwire your pc to the runner utilizing one of the 4 ports on the right.
After you make the connections from Cable modem to Router to PC.

1. Unplug both your modem and the wireless router
2. Keep unplugged for 30 seconds then plug your modem back in
3. Count an additional 20 seconds and then plug your router in

Wait a few minutes for the modem and the router to startup and begin communicating.
Finally click on your browser and test your connection... You should be in business,
Now that your internet is being broadcasted unsecurely, It would be in your best interest to secure it.
Follow these instructions and you should be in good shape
Wireless Securuty Linksys Setup

With the information you provided, it is possible that there is an ip conflict on your network that is why only one laptop can go online at a time. Please check the IP address of your laptop, if you are using Windows. Click on the Windows button and on the search box type in cmd (for command line). You will see a black box of the command prompt. Type in ipconfig/all on both computers to check if they have the same ip settings.

• Hello micheal_e_gu, go to this "Website" you'll be able to "Download the [PDF] "Manual / User;s Guide. I hope this information is helpful? Thanks for using FixYa, paul7of9" Click here: http://homesupport.cisco.com/en-us/wireless/lbc/WRT54GS

All you have to do is to find the pass-phrase (or password) for your wi-fi. Start your favorite browser (Internet Explorer, Mozilla etc) and at the address line type 192.168.1.1 and hit enter. This address is the typical address for linksys routers. At the page with the router's settings that will come up, go at the wireless tab and after this at the wireless security tab. There is an area for pass-phrase, write down at a piece of paper the phrase in this area because this is the pass-phrase you have to provide at the e-reader when it will ask you for a password to connect to the Wi-Fi.

In case of a problem or clarification or further details needed, don't hesitate to post me a reply before rejecting my answer.
If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Thanks and regards
Please kindly rate this solution
Stelios
direct fixya link: http://www.fixya.com/users/technical114