Top 20 Logitech X-530 Computer Speakers Questions & Answers

Did these come with a disk for installation? Did you check that the drivers are installed? Device Manager-Sound Devices.

My speakers in my 2003 Silverado started to fail at about 5 years old. I just replaced them with all new speakers. They would come and go erratically and sounded horrible.

My Dell Vostro computer does not recognise my Logitek speakers

replace with correct amperage (usually marked on the fuse) and see if it blows again---if so a problem exists.

did you check witch imput your pluged in?you should be in the green imput

the card got broke? epoxy it back together for the support and make sure all electrical connections from vol control are jumped from control to good side of board, see if u can find someone who has soldering experience if you dont an easy fix if vol control is not damaged alternative.... search ebay u may find someone selling those same speahers

Just anyway to gain access to open the box is ok there is no easy way really remove the screws (If) it has any or cut an access hole to reattach the wires just dont damage the speaker is all that needs to be watched for. Remember to rate my solution

if your sound is not working you can check that the plugs are in the computer correctly usally there are green and pink ends on computer speakers green indicating goes in the green slot and pink in the pink some people often gets confused and there are sometimes on new modles a blue slot that can look green in low light i would suggest checking they are plugged in correctly to the computer preferably in the back and not the front if the front option is avalible and check the appropriate drivers are installed on the computer to use the speakers

Connect the d-sub connector plug (the VGA cable,probably black colored) into the subwoofer.

that's very nice thought but realty is different do not open himself go to service center for logitech specialist for sound they repair accurate so go and repair by the logitech service center

click start control panel administrive tools ,computer management ,device manager scroll down image devices you could see a yellow question mark? right click to reinstall drivers or update driver open skype go to tools from the drop down list select options scroll to audio settings you can make a free test call before you try to make a call make sure the microphone is using the same as your computers audio you can make a free test call if you cant get the microphone to work you can select learn about setting up your audio equipment also click start control panel sounds and audio devices audio and also voice it's the same make sure that you have the right default microphone selected you should be able scroll to video settings to make sure you have the right settings Open skype go to tools options scroll to audio settings or video settings on the right you will see webcam setting you can change the settings from there click apply after changing any settings also you can see the webcam there you can even take a snapsot also make sure your settings are correct for a video call also click start control panel sounds and audio devices select advanced there might be a tick in the mute box untick also select audio from the microphone drop down list make sure you have the right one selected and in the volume box make sure the microphone box has a tick in it or select the voice tab and make sure that you have the right media selected also select volume make sure the box for microphone has a tick in it

When you are looking in "control panel", are you looking at "sound, audio and game controllers"?
To access that you will need to get into "device manager" and ckick on the box next to "sound, audio and game controllers". After you click on the box, you should have a list of your audio device(S). Right click on eqch one, on at a time and you should see "disable", If you see "enable", click on that. While you are looking at your device(s), what do you see, ie, Realtek, Soundblaster, etc, for you sound software. Depending on what you have, you may want to make sure you software is updated. I will start you off with these things to try, if this doesn't solve your problem or, if you have other questions, let me know.
Dave

Unfortunately you will not be able to use the sub-woofer by itself because the input for the Logitech X-530 has a special cable to connect to the sub-woofer. You could always try looking on eBay or Craigslist for replacement parts.

check out some step down transformersyou can check the link belowhttp://www.rpelectronics.com/170d-115-230-volt-500-watts.html

Hi names Rui i like to help you by giving you step by step instruction in propely hocking up your logitech speakers:

Instructions

1. Connect the black plug of the rear right speaker into the black plug on the subwoofer.

2. Connect the yellow plug on the rear left speaker into the yellow input on the subwoofer.

3. Connect the red plug of the front center speaker into the red input on the subwoofer.

4. Connect the white plug of the front left speaker into the white input on the subwoofer.

5. Connect the d-sub connector plug from the front right speaker into the d-plug connector on the subwoofer.

6. Connect the green, black and orange input to the matching plugs on your computer. If you have a four-channel sound card, connect the green plug from the input audio cable to the front plug of the card and the black plug to the rear plug. Do not connect the orange input. If you are using a two-channel sound card, connect the green plug from the input audio cable to the "Line Out" jack on the sound card. Do not connect the green and orange plug.

7. Plug the subwoofer power chord into the electrical power outlet.

8. Place your subwoofer on ground around your computer desk. Position the front center speaker on top of your computer monitor.

9. Place the left and right front speakers on the sides of the monitor. Position the left and right rear speakers behind you, making sure they are pointing toward the front left and right speakers.10. needs to support 5.1 surround. Normally, more than three sockets for sound indicates that it does. Then you need to use the software that comes with the sound hardware to configure it for 5.1 - Default will be 2.1 or just 2.Check the control panel out. This is a lot easier under Windows 7.- Here you can access what you need via the speaker icon on the system tray (right click)There is NO problem with your OS or hardware, this is pretty standard...hope this will help you solve your problem.

I had a similar issue and I could not fix it even after several attempts. I calledThe Best Pc Doctor Team and they fixed it for me.I am including their contact details here.www.thebestpcdoctor.com877 407 9229(Toll free)

Test all leads that attach to your hard drive including electrical extensions,IDE,SATA

the leads from your ((motherboard to your hard drive)) make sure they have a secure connection and are not faulty or just replace them there probably old and faulty make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even the electrical extensions or just replace them they could be faulty a computer needs its connections to continue its cycle and have an end so any faulty leads will end up with a computer error you might need to check the error so you know what the problem isclick start control panel administrive tools computer management then select event viewer depending on what operating sytem you have this may vary in left panel extend the events there you will see errors in red right panel you will no what exactly what the error was and at what time it occured you might be able to work your way through the problem if you need any further help with this post a replyhope this helps

You can't connect the speakers to your TV. I doesn't have any audio output available, just inputs. Those are for connecting the audio from sources like DVD players, and they go in to the TV's sound system. But there's no way of getting the sound out except through the set's internal speakers. The surround system you got is great for a computer, but it's not what you need for TV use.

The only solution I can offer is the suggestion that you invest in a home theater receiver. You can get decent basic systems with the receiver (often with DVD/audio CD playback capability built in) and surround speakers at reasonable prices. Then you use that to drive the speakers, and use the TV just as a video monitor. Then you will have surround sound.

Yes it is..Buy a to A/V cable where the out is the same with pc speaker plug while the A/V jack is for your T.V audio out or DVD audio out.

the input for the speakers need to be 5.1i guess you might have connected to 2.1 audio sourceif i am not wrong,you might have connected it to 2.1output of your PCtry connecting the same to an DVD or compact Disc players,which has 5.1output