Top 20 Xerox 212 Laser Printer - Page 5 Questions & Answers

Sad to inform you because unit is no longer repairable so the only thing you can do is to buy a new one.

That is a problem with the fuser and it could be the fuser or it could be the power supply. Xerox is proprietary and you will have to contact them with you wallet in hand to get this repaired.

I don't see a question ...............

It helps to know WHAT the problem is, but there are links to problems and also to support forums at Xerox here, manned by Xerox personnel. https://www.google.com/search?q=XEROX+WC+5024+PROBLEM ..

To resolve Epson wf-3640 error code 0x97 all you need to do is to check the basic settings of printer, restart your printer, check drivers updates, for more such steps visit - https://wearableworld.co/error-code-0x97/

Printers do not have a region.

Contact Xerox. There will be support online.

I had a Xerox 5035 copier and had a device called a Wiper that removes the remains of the old image on the drum to the toner sump. Seems that these wear and cause what you talk about. Good Luck there are service manuals, very hard to locate. I dropped the links after I gave mine away.

https://www.office.xerox.com/en-lb/multifunction-printers/workcentre-3315-3325/supplies

Try these solutions

• Power Off the Printer Using the Power Switch on the Lower Center Tray. Wait Two Minutes and Then Power On the Printer
• Remove the Toner Cartridge, Gently Shake the Cartridge 10 Times, and Then Re-install the Cartridge
• WorkCentre 7120/7125: Replace the Appropriate Drum Cartridge(s)

Xerox would be a possible source.

search on CWA0776 in internet search engine. or search compatible xerox 3210.3220 toner not sure if you can use inkstation but it is an example of the toner you are looking for being cwa0776 https://www.inkstation.com.au/1-fuji-xerox-workcentre-3210-3220-compatible-toner-cartridge-cwaa0776-p-4527.html?prt=3527&gclid=Cj0KCQiAzZL-BRDnARIsAPCJs71H_pfIzNXPVC8dr7YVX720vQDm01T5l7JRpYBJ7Pw0AXuND5BxGi8aAp1hEALw_wcB

https://www.support.xerox.com/en-us/article/en/1383928.html

"- To clear this fault, first remove the cause, next clear the value of NVM [744-248] to "0", and then turn the power OFF then ON. The flag of NVM [744-248] indicates 0: Normal, 1: NCS-Center abnormal high temperature value, 2: STS-Rear abnormal high temperature value, and 3: NCS and STS high temperature error. - When turning the power OFF, turn OFF the power switch first and then the main power switch."

Hi.

• Code: 045-310
• Description:Image Ready Error Unable to send the Image-valid signal cannot within the specified time. NOTE: When the attempt to expand the image has failed, [016-776 Marker Code Detection Fail] occurs after the recover operation.
• Remedy:1. Check the USB Cable (Local) for poor connection. 2. If no problem is found, replace the ESS/MCU PWB. (PL 18.1).

Good luck.

https://www.youtube.com/watch?v=1F1Jg0WKhSg https://www.youtube.com/watch?v=peMs-DIObIs

Try this link: https://www.support.xerox.com/en-us/article/en/1048969

If you are several sub-menus deep inside the Diagnostic menu hierarchy, you will need to press the [Exit] button several times to return to the previous menu, and until you finally exit the Diagnostic mode.

Ensure that the flat side of the Xerographic latch is tight against the flat edge in the indentation on the front of the Xerographic module. Press on the left side of the toner cartridge to ensure the developer assembly is touching the Xerographic module.

There is information about your device here >> https://www.youtube.com/watch?v=5o6coqwhZ54 << Paste this into the search >> xerox wc 7435 error code 010-337 what is the solution << for more videos... Regards Geoff