20 Most Recent Xerox Phaser 7300DN Laser Printer - Page 2 Questions & Answers

Yes. Take a look here - you'll find all the information you need on how to do it.

My advice is to throw the printer out the window!! Just a suggestion!

Ted

Hi,
Sometimes on this machine as there is a lot of loose toner around it can cover over the sensors in the machine, what I would advise is to remove all the toner cartridges and check for the copper contacts on both the machine and under the imagining unit (which the toner is placed in). Once you have cleaned that away slowly close the lid and reboot the machine and it should return to normal. Its just toner getting caught up in the sensors. Follow the instructions below, when you remove the unit, lift it over your head to find the copper contacts and clean them, be careful not to spill toner everywhere. Good luck!

Reseating the imaging unit

Remove the toner cartridge:

1. Open the top cover.
   
   The imaging units are sensitive to light. Do not expose the imaging units to light any longer than necessary to remove it and cover it. Failure to follow these instructions may damage the imaging units.
   
2. Identify the color of the toner cartridge to be replaced (Cyan, Magenta, Yellow or Black).
   
   
3. Move the orange lever on the toner cartridge to the right so that it unlocks.
   
   
4. Lift on the back side of the toner cartridge first, then guide the cartridge out of the printer.
   
   
5. Set the toner cartridge on paper to avoid any toner spilling.
   
   Reseat the imaging unit:
   
6. Lift the imaging unit straight up out of the printer.
   
   
7. Line up the guide pins with the printer's frame and lower the imaging unit back into the printer.
   
   Reinstall the toner cartridge:
   
8. Install the toner cartridge by guiding the front onto the new imaging unit first then lowering the back.
   
   
9. Move the orange lever on the toner cartridge to the left so it locks.
   
   
10. Clean the LEDs with the supplied wipe.
    
    
11. Close the top cover.
    

The flashing light indicates a warning state - such as low toner - but it will not stop the printer working, so there must be more than one issue if it is not printing at all. A flashing orange will be accompanied by a message on the screen to indicate which item(s) is/are in a low state.

These are 2 different problems. The fusing issue is that the fuser roller is controlled by the "ATC Anvil calibration". This requires Transparencies (PN 42527801) to be run through the Manual feeder. You may need a technician for that, or buy a manual

The "reseat message" is probably a warping "top cover inner frame" 116-1548-00. You might need to replace that whole top.

Whit
Item, Inc.

Check out the suggestions on my web page article :

http://michelsplace

You can reset the counter using the service menu. You can find full details of how to do this on my website here.This will solve your problem.

U6 is a low voltage psu failure. It may be that the power connector to the engine controller board became dislodged during the move. You can check the details in the manual which you can download here.

I would choose DT, then you'll have the duplex function in the driver. The DT is the same as the DN, but has an extra paper tray.

Yes, this can be done - it's a relatively simple process. Take a look here where you'll find all you need to know about doing it, plus a load of other useful information about this printer.

You can reset the imaging unit in two ways - either with a fuse, which will return the count to 100%, or in the hidden menu, which will not get you all the way to 100%. You'll find all the details about how to do it, and a lot more information about this printer here.

This is a common issue with the 7300. You can read all the details, including possible solutions here.

Better if you have other person to help you.

Turn off the printer, hold 0 3 5 6 7 buttons, turn on the printer, wait until the *s disapair.

sorry, I have the same problem, bought a new fan but still don't know how to install it... So if you have a solution/guide or something please let me know!

Hi

You need to disconnect the printer cable > turn off the printer > uninstall a pll components of the the printer program > restart the computer > power the printer on > reconnect the USB printer cable > reinstall the printer driver and applications, payinfg careful attention to any option boxes about the type of connection.

I hope this helps